MCR/TSR Alpha Series Remotes
5
4) Use
the
Group
Ï
and
Group
Ð
buttons to scroll through the character list. When the desired character has
been reached, press the
Scan
button once to store the character and advance to the next position. Repeat
Step 4 to store subsequent characters.
5)
When the last character has been stored, press the
PTT
button to store the message.
(Note: In the event of storing a character in the 9
th
position: do not press PTT, continue to Step 6.)
6)
Repeat Steps 2, 3, 4 until all desired groups and channels have been programmed with messages.
7) Press
the
PTT
button twice to exit programming mode and begin normal operation.
MCR211a, TSR(K)100a
1)
Press and hold the
Zone
Ï
button while turning power on to enter programming mode. When released, the
display will read “1-1” with its associated message.
2) Using
the
Zone
Ï
,
Zone
Ð
,
Channel
Ï
, and
Channel
Ð
buttons, select which zone and channel to enter/edit
programming. The zone/channel numbers will increment or decrement one digit for each short press and will
rapidly increment/decrement when pressed and held.
3) Press
the
Scan
button. A solid cursor will appear under the first/next position of the message.
4) Use
the
Zone
Ï
and
Zone
Ð
buttons to scroll through the character list. When the desired character has
been reached, press the
Scan
button once to store the character and advance to the next position. Repeat
Step 4 to store subsequent characters.
5)
When the last character has been stored, press the
PTT
button to store the message.
(Note: In the event of storing a character in the 9
th
(MCR211a) or 8
th
(TSR(K)100a) position: do not press PTT,
continue to Step 6.)
6)
Repeat Steps 2, 3, 4 until all desired zone and channels have been programmed with messages.
7) Press
the
PTT
button twice to exit programming mode and begin normal operation.
Cloning - All Models
Once a complete list of messages have been manually entered on a single remote, the message data can be
copied from that remote to any number of remotes connected to it.
1)
Connect the other remotes together using the same wiring system that will be used for normal operation with
the exception of the termination panel.
The termination panel must be disconnected or switched off.
2)
Cloning is initiated by pressing and holding the
Channel
Ð
button (MCR210a, 310a, 410a, 212a),
System
Ð
button (TSR411a, 412a),
Group
Ð
button (MCR411a), or
Zone
Ð
button (MCR211a, TSR(K)100a)
on the
remote with the programmed information
, while turning power on. When the button is released, the display
will read “COPYING”.
3)
The data copying process takes from twenty seconds to four minutes, depending upon the size of the
message data being transferred. A typical system will finish copying in less than one minute. When cloning is
finished, the “COPYING” message is replaced with a channel number indication on both the sending and
receiving remotes. All remotes in the system are ready for normal operation once the termination panel is
reconnected or powered on.
4)
After all remotes in the system have been programmed, it is recommended to place dip switch 3 in the “ON”
position on all remotes to disable the cloning function being recognized from parallel remotes. This will
prevent accidental erasure of the alpha information.
Erasing - All Models
The entire message EEPROM can be erased in a single operation on individual remotes.
1)
Erasing is initiated by pressing and holding the
Monitor
button (MCR210a, 310a, 410a, 212a) or the
Scan
button (TSR411a, 412a, MCR411a, 211a, TSR(K)100a) while turning power on. When the Monitor or Scan
button is released, the remote will display “ERASING” or “
” on some models.
2)
Once all information has been erased, the “ERASING” or “
” message will be replaced with
“ch00”, “Ch01”, or “1-1”, the message data will be erased, and the remote enters the channel select mode of
programming.
3) Pressing
the
Scan or P Scan
button (MCR210a, 310a, 410a, 212a) or
PTT
button (TSR411a, 412a,
MCR411a, 211a, TSR(K)100a) two times exits the erasing mode, leaving the message memory erased.