background image

SPECIFICATIONS

XM6 — 2-/4-/6-CHANNEL 2-/3-WAY CROSSOVER

Dual High Pass Crossover:

18dB/Oct 40Hz-400Hz

Frequency Multiplier:

x20 (18dB/Oct 800Hz-8kHz)

Band Pass Crossover:

18dB/Oct 300Hz-3kHz (HP)

18dB/Oct 40Hz-400Hz (LP)  

Low Pass Crossover: 

36dB/Oct Mono 40Hz-200Hz 

Bass Drive:

0dB to 18dB

Bass Shaper Eq:

40Hz to 100Hz

Bass Shaper Boost:

0dB to 18dB

Phase Switch:

0˚/180˚

Max Input/Output:

8Volts RMS

Input current:

1 amp max.

Frequency response:

20Hz–20kHz 

±

1

4

dB before crossover limit

Separation:

60dB

THD+N:

<0.1%

Signal to Noise:

>90dB

Input Impedance:

>10k Ohms

Output Impedance:

50 Ohms

Dimensions: 2

3

16

” H x 8

1

2

” W x 6

7

8

” L 

(55mm x 216mm x 174mm)

Due to continual product development, all specifications 

are subject to change without notice.

WWW.COUSTIC.COM

23

ADJUSTMENTS cont.

BASS SHAPER BOOST AND EQ

The optimum setting for this feature will vary depending upon the low 

frequency response of the vehicles interior. Set the “Boost” control half way

between 0dB and +18dB. Starting from the preset frequency, gradually

adjust the “Frequency” control downward or upward until you get a smooth

even bass response. Once the frequency has been chosen, you may increase

or decrease the equalization by adjusting the “Boost” control upward or

downward.   

NOISE CHECK

• Before mounting the XM6 crossover and the other audio components

permanently, please conduct the following noise check: 

• Start the engine and turn on the power of the source unit.

• Rev the engine and vary the audio volume to check for radiated

engine noise. If there is an alternator whining noise or tic-tic noise,

refer to the TROUBLESHOOTING GUIDE for assistance. If the problem

persists, consult your local Coustic dealer or Coustic directly.

• If no unwanted noise is detected, double check all the wiring and

cables for safe placement. Then securely tighten the mounting screws

of all the audio components.

Summary of Contents for XM6
















Reviews: