Country Flame Inglenook IWZC-02 Owner'S Manual Download | Manualshive

Page: 25 / 54

background image

FIGURE 14: COMUSTIBLE FACING

FIGURE 15: NON-COMBUSTIBLE FACING

MANTEL CLEARANCES:

Option 1: When installing the unit

without

the gravity duct kit the mantel must be at least 71” from

the base of the unit.

Option 2: When installing the unit

with

the optional gravity duct kit the mantel must be at least 55

inches from the bottom of the unit.

Option 3: When installing a brick/stone facing protruding 3 ½ inches from the front of the unit, the

mantel must be at least 59 inches from the base of the unit.

Option 4: When installing the unit using the optional hot air block –off kit and the gravity duct kit,

the mantel must be at least 45 inches from the bottom of the unit.

MOBILE HOME INSTALLATION AND CEARANCES:

The Inglenook Fireplace has been tested and approved for installation in mobile homes. It is
important to follow additional installation requirements associated with mobile home installation.
Then Inglenook Fireplace must be securely fastened to the floor of the mobile home using the system
provided by Country Flame. Figure 16 demonstrates the recommended “tie down” points for use in
securing the Inglenook Fireplace to a mobile home floor. In addition, the Inglenook Fireplace should

NEVER BE INSTALLED IN THE SLEEPING AREA OF ANY MOBILE HOME

. Also, the

structural integrity of the mobile home floor, wall, ceiling, and roof must be maintained during the
installation of an Inglenook Fireplace in a mobile home application. If there are any questions
concerning mobile home installation, contact your local Country Flame dealer and adhere to all local
codes concerning mobile home installation.

Version: 7.0

25

FIGURE 16: INGLENOOK TIE DOWN POINTS

«
...
23
24
25
26
27
...
»

Summary of Contents for Inglenook IWZC-02























































Reviews:

No comments

Related manuals for Inglenook IWZC-02

Brand: Parkwood Pages: 40

Brand: Panadero Pages: 30

Brand: Majestic Pages: 20

Brand: Desa Pages: 4

BAYPORT-41 GLASS

Brand: kozy heat Pages: 49

Brand: OVE Pages: 16

Brand: Nu-Flame Pages: 15

Brand: Jøtul Pages: 120

Brand: Kingsman Pages: 59

Brand: Costway Pages: 10

Brand: Majestic Pages: 79

Brand: Jensen Pages: 48

Brand: Charlton & Jenrick Pages: 32

Brand: GlammFire Pages: 24

Contura C810 Style

Brand: Nibe Pages: 40

VIVALDI DE LUXE VVLD20

Brand: EWT Pages: 32

Brand: Nibe Pages: 20

Brand: Mason-Lite Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands