background image

- 1 - 

TIRE CHANGER 

INSTRUCTION MANUAL 

INDEX 

 

              INDEX                                                                                                                            PAGE 
1.  Technical Data                    ----------------------------------------------------------------- 
2.  General safety warnings and precautions        --------------------------------- 
3.  Specific Product Warnings And Precautions      --------------------------------- 
4.  Assembly Instruction        ------------------------------------------------------------ 

4-1 Transport 
4-2 Unpacking 
4-3 Product Description 
4-4 Workplace Requirements 
4-5 Assembly Procedure 
4-6 Pneumatic Link Up 
4-7 Electric Link Up 

5.  Warning Label  ----------------------------------------------------------------------------- 
6. Operating 

Instructions   ------------------------------------------------------------------ 

6-1 To Perform Preliminary Operating Texts   
6-2 To Break The Tire Bead 
6-3 Demounting The Tire From The Wheel 
6-4 Mounting The Tire Onto The Wheel Rim 
6-5 Inflating The Tire 

7.  FRL Instruction        ------------------------------------------------------------------- 
8.  Routine Maintenance   ------------------------------------------------------------------- 
9.  Trouble Shooting Guide    ----------------------------------------------------------------- 
10.  Mounting Head’s Angle Adjusting    ----------------------------------------------------- 

11. 

Exploded Drawings And Spare Parts List                ---------------------------------

 
 
 

 
 
 
 
 
 

 
 

 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

 

10 

11 

12 

14 

15 

Summary of Contents for C211 C































Reviews:

Related manuals for C211 C