background image

 

 
 
 
 
- Do not spray insecticide on the fan               - Do not hang any clothes to dry on the 
  as shown in the picture below. It is                  fan guard as per the picture shown              
  dangerous to the user and also will                 below. This is a dangerous act as 
  damage the painted parts.                               the clothes might get stuck into the  
                                                                           fan blade and may cause a lot others                            
                                                                           unwanted damages. 
 

 

      

    

 
 
 
 
1. Always disconnect the appliance from the power supply before cleaning. 
 
2. The fan only needs some general external cleaning. 
 
3. Clean the outer parts with kitchen detergent. Then wipe it clean with a soft dry  
    cloth. 
 
4. Never use water to clean the appliance. 
 
5. To avoid decolouring or deterioration. Do not use thinner, toluene, acid   
    detergents, kerosene, alcohol or cloth chemical to wipe the parts. 
 
6. For proper storage. After doing the maintenance, follow the original packing order  
    for properly storage. 
 
7. Always store the fan at a dry place. 
 
 

 

 
 
 
 
 
 
 
 
 

SPECIAL PRECAUTIONS 

CARE AND CLEANING 

Summary of Contents for CFN-E161RC









Reviews: