Coram Showers OPTIMA Series Manual Download Page 14 | Manualshive

Page: 14 / 16

background image

Fixed Panel

14

Fit the door handles to the door ensuring the supplied
handle washers are used on each side of the glass.
A chrome finish handle is supplied for all frame finish
options.

15

c

b

a

The 'cam adjusters' at the top and bottom of the door may need adjusting so that the door slides freely and the magnetic seal is
flush against the magnetic profile when the door is closed.

a:

Loosen all 4 cam adjuster screws (1 turn maximum).

b:

Turn the cam adjusters (by hand or using a 16mm spanner) until the

door hangs vertically. Re-tighten the screws -

do not over tighten

.

c:

Push fit all 4 covers (PN50103) onto the door.

14

From inside

PN50103

Lubricate the inner
top and bottom
rails using the wipe
provided.

PN60058

16

17

PN50382

PN3222

PN4745

Fit the Bump Stops to the
rail,

top

and

bottom

as

shown on the fixed panel
side. Tighten the screw with
a screw driver,

do not

over

tighten. Place cover cap in
the hole.

«
...
12
13
14
15
16
»

Summary of Contents for OPTIMA Series

















Reviews:

No comments

Related manuals for OPTIMA Series

Brand: Insignia Pages: 24

Brand: Insignia Pages: 27

Brand: Insignia Pages: 27

Fuenta New DWJS

Brand: Radaway Pages: 26

Brand: THE SHOWER LAB Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands