Cooper Menvier 100 Installation Manual Download Page 37

Menvier40/100 

Technical Specification 

Page 33 

Other 

If you wish to connect the control unit to a 
PC using either the Ethernet or the USB 
port then make sure that the cables have 
the following specifications: 

Ethernet 

Cat5e patch cable, RJ45 
male plugs at each end, 
suitable for 10/100Base-T. 

USB 

Mini-B plug for control unit 
end, USB-A for PC end. 
Max length 3m.  

Radio Expander and Keypads 

Radio 

Operating frequency 
868.6625MHz Narrowband. 

  

EN 300 220-3. 

 

EN 300 330-2 

Transmitter 
range 

The range of the 
transmitters compatible 
with this control unit 
depends on the 
environment in which they 
are installed. As a 
guideline, most 
transmitters will work up 
200m range in free space 
conditions. 

 

Compliance Statements 

The Menvier40 and Menvier100 are 
compliant with EN50130-5 environmental 
class II. 

The Menvier40 and Menvier100 are suitable 
for use in systems designed to comply with 
PD 6662: 2010 at grade 3. 

When installed correctly the Menvier40 and 
Menvier100 are capable of compliance with 
EN50131 at Grade 3. 

To maintain Grade 3 the Menvier40 and 
Menvier100 must be fitted with a 
communicator of level ATS4 or above. 

When fitted with radio devices the 
Menvier40 and Menvier100 are capable of 
compliance with EN50131 at Grade 2. 

The i-sd02 is compliant with EN50136-1 as 
an ATS2 communicator. 

The i-sd02 may be used as a 
supplementary communicator at Grade 3.  

At Grade 2 the i-sd02 provides a compliant 
communicator for the Menvier40 and 
Menvier100 provided that: 

a)  It is installed in accordance with the 

installation instructions. 

b)  The connected PSTN is functioning 

normally. 

When fitted with an i-sd02 the control unit 
provides options A, B and C at Grade 2 as 
noted in Table 10 of EN50131-
1:2006+A1:2009. 

If the installer selects a non-compliant 
configuration then they must remove or 
adjust compliance labelling 

Third party testing carried out by Anpi. 

Compatible Equipment 

705rEUR-00 

Two button HUA (top 
button is disabled) 

703rEUR-00 

4-channel (2 zone) 
transmitter 

706rEUR-00 

Two button HUD/tilt 
switch transmitter 

710rEUR-00 

Two button HUD 

713rEUR-00 

Pet tolerant PIR 

714rEUR-00 

PIR Transmitter (Small 
case) 

720rEUR-00 

Smoke Detector 
Transmitter 

726rEUR-50 

Long range hand held HUD 

726rEUR-60 

Short range hand held HUD 

727rEUR-00 

Four button remote 
control with encrypted 
code (HUD function not 
compatible with BS8243) 

734rEUR-00/01  CC/FSL Door Contact 

Transmitter (white) 

734rEUR-05/06  CC/FSL Door Contact 

Transmitter (brown) 

738rEUR-00/04  Spyder shock sensor 

(white/brown) 

739rEUR-50 

Sentrol glass break 
detector (no tamper) 

760ES 

External Wireless 
sounder 

762rEUR-00 

Two Channel Receiver 

768rEUR-50 

Eight Channel Receiver 

770rEUR-00 

Wireless Accessory 
Module (repeater mode 
only) 

08844EUR-00 

GPRS module (obsolete) 

Summary of Contents for Menvier 100







































Reviews: