Cooper Menvier 100 Installation Manual Download Page 2

Page ii 

© Cooper Security Ltd. 2012 

IN NO EVENT WILL COOPER BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL , OR INDIRECT LOSS OR DAMAGE, 

INCIDENTAL DAMAGES, STATUTORY DAMAGES, EXEMPLARY DAMAGES, LOSS OF PROFITS, LOSS OF REVENUE, LOSS 

OF ANTICIPATED SAVINGS, LOSS OF BUSINESS OR OPPORTUNTIY, LOSS OF GOODWILL OR INJURY TO REPUTATION, 

LIQUIDATED DAMAGES OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.  COOPER‟S 

LIABILITY FOR DAMAGES ARISING OUT OF OR RELATED TO A PRODUCT SHALL IN NO CASE EXCEED THE PURCHASE 

PRICE OF THE PRODUCT FROM WHICH THE CLAIM ARISES.  TO THE EXTENT PERMITTED BY APPLICABLE LAW, THESE 

LIMITATIONS AND EXCLUSIONS WILL APPLY WHETHER COOPER‟S LIABILITY ARISES FROM BREACH OF CONTRACT, 

BREACH OF WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE), STRICT LIABILITY, BY OPERATION 

OF LAW, OR OTHERWISE. 

Every effort has been made to ensure that the contents of this book are correct. The contents 
of this book are subject to change without notice. 
Printed and published in the U.K. 
This manual applies to the Menvier40 and Menvier100 control units with version 4.03 software. 

For Your Safety 

This book contains several passages alerting you to potential problems or hazards. Each of 
these are marked by the words 

Note

Caution

 or 

WARNING

.: 

Note:

 

Describes conditions that may affect the proper functioning of the equipment 
(but will not damage the equipment). 

Caution:

 

Describes actions that will physically damage the equipment and prevent its 
proper function. 

WARNING:

 

Describes actions that are hazardous to health, or cause injury or death. 

Please pay particular attention to these marked passages. 

Terminology 

With the introduction of BS8243 and PD6662:2010, Cooper Security have changed the name 
“panic alarm” to “hold up alarm” and “PA” to “HUA”. 

Other Publications for the Menvier40 and Menvier100: 

The following guides are available from the Cooper Security website: 

www.coopersecurity.co.uk

 

Quick User Guide 

Brief instructions for setting and unsetting alarm systems 
based on Menvier40/100/300 control units. 

Menvier40/100/300 Engineering 
Guide 

A detailed description of the Installer‟s programming 
options. 

Menvier40/100/300 
Administrator‟s Guide 

Detailed notes for the system administrator of an alarm 
system based on the Menvier40/100/400. 

Web Server Setup Guide 

Instructions on how to configure a Windows PC or laptop to 
use the Menvier40/100/400‟s built-in web server for 
installation programming. 

Cooper Downloader Quick Guide  Instructions for how to install Cooper Downloader on your 

PC or laptop, and connect to Menvier40/100/300 Control 
Units. 

Menvier Updater Installation 
and User Guide 

Instructions on how to install Menvier Updater on your PC 
and use it to update the software on your 
Menvier40/100/300 control unit. 

www.coopersecurity.co.uk 
Product Support (UK) Tel: +44 (0) 1594 541978.  
Available between: 
08:30 to 17:00 Monday to Friday.  
Product Support Fax: (01594) 545401 
email: [email protected] 
Part Number 12232039 

4/5/2012 

Summary of Contents for Menvier 100







































Reviews: