Cooper & Hunter CH-S07FTXK-NG, Owner'S Manual

Page: 21 / 105

Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Function introduction for
combination buttons
Ɣ
button
no display
Ɣ
Ɣ
Ɣ
When selecting " " or no display with remote
controller, temperature indicator on indoor unit
displays set temperature.
When selecting " " with remote controller,
temperature indicator on indoor unit displays
indoor ambient temperature.
When selecting " " with remote controller,
temperature indicator on indoor unit displays
outdoor ambient temperature.
By pressing this button, you can see indoor set
temperature, indoor ambient temperature or
outdoor ambient temperature on indoor unit's
display. The setting on remote controller is select-
ed circularly as below:
Energy-saving function
Ɣ
Ɣ
Ɣ
Ɣ
Child lock function
8
ȭ
heating function
Outdoor temperature display is not available for some
models. At that time, indoor unit receives " "
signal, while it displays indoor set temperature.
It's defaulted to display set temperature when turning
on the unit. There is no display in the remote control-
ler.
Only for the models whose indoor unit has dual-8
display.
When selecting displaying of indoor or outdoor ambi-
ent temperature, indoor temperature indicator
displays corresponding temperature and automatical-
ly turn to display set temperature after three or five
seconds.
Temperature display switchover function
Under energy-saving function, fan speed is defaulted
at auto speed and it can't be adjusted.
Under energy-saving function, set temperature can't
be adjusted. Press "TURBO" button and the remote
controller won't send signal.
Sleep function and energy-saving function can't oper-
ate at the same time. If energy-saving function has
been set under cooling mode, press "SLEEP" button will
cancel energy-saving function. If sleep function has
been set under cooling mode, start up the ener-
gy-saving function will cancel sleep function.
Under OFF status, press " ź " and "MODE" buttons
simultaneously to switch temperature display
between °C and °F.
Under cooling mode, press "TEMP" and " CLOCK"
buttons simultaneously to start up or turn off ener-
gy-saving function. When energy-saving function
is started up, "SE" will be shown on remote con-
troller, and air conditioner will adjust the set tem-
perature automatically according to ex-factory
setting to reach to the best energy-saving effect.
Press "TEMP" and "CLOCK" buttons simultane-
ously again to exit energy-saving function.
NOTE
NOTE
Press Ÿ " and ź " simultaneously to turn on or
turn off child lock function. When child lock func-
tion is on, " " icon is displayed on remote control-
ler. If you operate the remote controller, the " "
icon will blink three times without sending signal to
the unit.
NOTE
TEMP
Under heating mode, press "TEMP" and "CLOCK"
buttons simultaneously to start up or turn off 8
ȭ
heating function. When this function is started up,
" " and " 8
ȭ
" will be shown on remote controller,
and the air conditioner keep the heating status at
8
ȭ .Press "TEMP" and "CLOCK" buttons simulta-
neously again to exit 8 ȭ heating function.
Under 8
ȭ
heating function, fan speed is defaulted at
auto speed and it can
'
t be adjusted.
Under 8
ȭ
heating function, set temperature can
'
t be
adjusted. Press "TURBO" button and the remote
controller won
'
t send signal.
Sleep function and 8
ȭ
heating function can
'
t operate
at the same time. If 8
ȭ
heating function has been set
under cooling mode, press "SLEEP" button will cancel
8
ȭ
heating function. If sleep function has been set
under cooling mode, start up the 8
ȭ
heating function
will cancel sleep function.
Under
ȯ
temperature display, the remote controller
will display 46
ȯ
heating.
button
Press this button to turn off display light on indoor
unit. " " icon on remote controller disappears.
Press this button again to turn on display light.
" " icon is displayed.
LIGHT