Cooper & Hunter CH-S07FTXK-NG, Owner'S Manual

Page: 19 / 105

button
button
button
button
Ɣ
Press this button can select left & right swing
angle. Fan blow angle can be selected circularly
as below:
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Press this button continuously more than 2s, the main
unit will swing back and forth from left to right, and
then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immedi-
ately.
Under swing left and right mode, when the status is
switched from off to , if press this button again
2s later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence
stated above.
This function only applicable for some models.
Press Ÿ or " ź " button once increase or
decrease set temperature 1°C (°F +ROGLQJŸRU
" ź " button, 2s later, set temperature on remote
controller will change quickly. On releasing button
after setting is finished, temperature indicator on
indoor unit will change accordingly. (Temperature
can't be adjusted under auto mode)
When setting T-ON, T-OFF or CLOCK, press
Ÿ "
or " ź " button to adjust time. (Refer to CLOCK,
T-ON, T-OFF buttons)
Ɣ
"
、 、
" may not be available. When air
conditioner receives this signal, the air conditioner will
blow fan automatically.
Press this button continuously more than 2s, the main
unit will swing back and forth from up to down, and
then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immedi-
ately.
Under swing up and down mode, when the status is
switched from off to , if press this button again 2s
later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence
stated above.
Under COOL or HEAT mode, press this button to
turn to quick COOL or quick HEAT mode. " "
icon is displayed on remote controller. Press this
button again to exit turbo function and " " icon
will disappear.
If start this function, the unit will run at super-high
fan speed to cool or heat quickly so that the ambi-
ent temperature approachs the preset temperature
as soon as possible.
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
no display
position)
(stops at current
button
When selecting " ", air conditioner is blowing
fan automatically. Horizontal louver will automat-
ically swing up & down at maximum angle.
When selecting "
、 、 、 、
", air condi-
tioner is blowing fan at fixed position. Horizontal
louver will stop at the fixed position.
When selecting "
、 、
", air conditioner is
blowing fan at fixed angle.
Hold " " button above 2s to set your required
swing angle. When reaching your required
angle, release the button.
Press this button can select up & down swing
angle. Fan blow angle can be selected circularly
as below:
no display
(horizontal louvers stops
at current position)
TURBO
T-ON T-OFF
NOTE
NOTE
T-ON button
"T-ON" button can set the time for timer on. After
pressing this button, " " icon disappears and
the word "ON" on remote controller blinks. Press
Ÿ or " ź " button to adjust T-ON setting. After
each pressing Ÿ or " ź " button, T-ON setting
will increase or decrease 1min. Hold Ÿ or " ź "
button, 2s later, the time will change quickly until
reaching your required time. Press "T-ON" to
confirm it. The word "ON" will stop blinking." "
icon resumes displaying. Cancel T-ON: Under
the condition that T-ON is started up, press
"T-ON" button to cancel it.
T-OFF button
"T-OFF" button can set the time for timer off.
After pressing this button," " icon disappears
and the word "OFF" on remote controller blinks.
Pre
VVŸ or " ź " button to adjust T-OFF setting.
After each pressing Ÿ or " ź " button, T-OFF
setting will increase or decrease 1min. Hold " Ÿ "
or " ź " button, 2s later, the time will change
quickly until reaching your required time. Press