background image

 
 

Page | 9 

 

  

 

 

 

 

 

 
1-6 In the Event of Shipping Damages 

 

IMPORTANT! 

According to the contract terms and conditions of the Carrier, the responsibility of the 
shipper ends at the time and place of shipment. 
The Carrier then assumes full responsibility of the shipment. 

 
 

  

Notify the transportation company's local agent. 

  

Hold the damaged goods and packing material for the examining agent's inspection. 
Do not return any goods to Fleming Dynamics before the transportation company 
inspection and authorization. 

  

File a claim against the transportation company. Substantiate the claim by referring to 
the agent's report. A certified copy of our invoice is available upon request. The 
original Bill of Lading is attached to our original invoice. If the shipment was 
prepaid, write us for a receipted transportation bill. 

  

Advise Fleming Dynamics regarding your wish for replacement. 

 

1-7 If the Shipment is Not Complete 

Check the packing list. The apparent shortage may be intentional. Back-ordered items are 
noted on the packing list. You should have: 
 

  

PCA Series Chiller 

  

Bill of Lading 

 

Packing List 



Operating and Installation Packet 

Re-inspect the container and packing material to see if smaller items have been missed 
during unpacking. Determine that the item was not taken from the area before the shipment 
was checked in. Notify Fleming Dynamics immediately of the shortage.  

 

1-8 If the Shipment is Incorrect 

  

If the shipment is not what you ordered, contact Fleming Dynamics immediately. 
Include the order number and item. 

  

Hold the items until shipping instructions are received.

 

Summary of Contents for PCA050












































Reviews: