manualshive.com logo in svg

Contura Surround C 11, Installation Instruction, Page: 29 / 36

Share
Download
Contura Surround C 11 Installation Instruction Download Page 29

GB

65

Installation height extension sections C11, C21

Note the different installation methods of the height 
extension section. When the protective firewall provided 
is not used the air outlet at the rear edge of the top panel 
must be plugged. 

In combination with non-flammable wall and chimney connection angled back through the height extension section.

Install the surround at ordinary height according to 
page 47-56. Block the air outlet at the rear edge of 
the top panel using the seal plate that is bonded into 
position using silicone. 

Apply silicone to the top of the surround and lift up 
the concrete sides of the height extension section. 
Support the first side so that it does not fall while 
the other side is installed. 

Hang the safety rail between the sides and ensure 
that they are straight. Check that the width is the 
same as section 1 at the front and rear edges. 

!

Connect the insert upwards and backwards 
within the given heights.  

ASSEMBLY

Summary of Contents for Surround C 11





































Reviews:

No comments