manualshive.com logo in svg

Contura Surround C 11, Installation Instruction, Page: 20 / 36

Share
Download
Contura Surround C 11 Installation Instruction Download Page 20

GB

56

10

10

VANAD

IUM

No. 7

CHROME

On aluminium and steel fronts there are adjustment screws that 
can be used to adjust the front panel by height. When the front 
panel is set the outer Torx screws are screwed until they support 
against the concrete. The top rests on the turned down angles at 
the rear edge, these can be adjusted to get the top to the level of 
the concrete.

When installing the height extension section:

•     with an integrated protective screen, go to page 58.
•     in combination with a non-flammable wall and  

 

chimney connection straight backwards, go to page 62.

•     in combination with a non-flammable wall and  

 

 

chimney connection angled backwards through the   

       

height extension section, go to page 65. 

For installations without height extensions, top 
connection to stainless steel flues is now possible; 
follow the chimney manufacturer’s instructions.
Then continue on page 57 with joining and painting.

Final inspection of the installation

Before the stove is used, it must be inspected by an authorised chimney sweep. Read the “Instructions for 
Lighting the CI 10 / CI 20 series” before lighting the fire for the first time.

ASSEMBLY

Summary of Contents for Surround C 11





































Reviews:

No comments