background image

PRODUCT INSTALLATION CONTINUED

4.  Remove Top Cover To Control Panel:  IMPORTANT:  First make sure power supply is unplugged from 

power source.

  Then remove the top cover of the control panel by unfastening the 4 screws as shown in the 

picture below allowing the top cover to freely separate from the bottom section of the control panel.  

5.  Fasten Bottom Section Of Control Panel To Skirting:

  Locate the two fastening holes as shown in the pic

-

ture below.  Use the supplied screws to securely fasten the bottom section of the control panel to the skirting.

6.  Fasten Top Cover of Control Panel:

  Make sure the black rubber gasket is secured in the grove on un-

derside of the top cover.  Replace the top cover of the control panel and securely tighten the 4 panel cover 

screws.    

WARNING:  Do not remove power cable or cell cable from the connectors inside the control 

panel.  Should cables become disconnected, make sure they are reconnected with the correct polar-

ity.  Reversing will damage the control panel.

Unfasten Screws

Unfasten Screws

Watertight Cable Grips

Fastening Holes

Fastening Holes

Summary of Contents for ChlorMaker IL













Reviews: