Control Network Solution eNodeIVTM User Manual Download Page 44

Page: 44 / 76

September 2011

V1.44

Device Name

: The name of the device.

IP Address

: The current IP address of the device.

IP Port

: The current IP Port number on which the device is communicating.

Multicast Address

: The address that the device uses if it is set to multicast addressing.

Channel Name

: The name of the channel to which the device belongs.

IP Support

: The protocols supported by this device. These include

UDP

TCP

, and

Multicast

709.1 Router Type

: The type of router of the device. The possible types are

Configured

Repeater

, or

Flood

Node Type

: The mode in which the router is operating. The only type currently supported is

Conventional Router

Subnet/Node

: The ANSI/EIA 709.1 subnet number and node number of the device. This

information is not always available.

Domain (HEX)

: The domain number of the ANSI/EIA 709.1 device. This information is not

always available.

Node ID (HEX)

: The IP-side Node ID of the device.

Get Device Data

: Clicking this button will retrieve all of the information from the device and

update the Device Detail Page. This button is not displayed on the device detail page of the

local device.

Summary of Contents for eNodeIVTM










































































Search results

Summary of Contents for eNodeIVTM

Reviews:

Brands by name

Popular brands

Control Network Solution eNodeIVTM, User Manual

Search results

Summary of Contents for eNodeIVTM

Reviews:

Brands by name

Popular brands