2
W415-1364 / 12.08.14
EN
TABLE OF CONTENTS
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
1.0
INSTALLATION OVERVIEW
3
2.0 INTRODUCTION
4
2.1 DIMENSIONS
5
2.1.1
BCDV36CF / BCDV36CFG
5
2.2 GENERAL
INSTRUCTIONS
5
2.3 GENERAL
INFORMATION
6
2.4
RATING PLATE INFORMATION
7
3.0 VENTING
7
3.1
VENTING LENGTHS AND COMPONENTS
8
3.2
TYPICAL VENT INSTALLATIONS
9
3.3
SPECIAL VENT INSTALLATIONS
11
3.3.1 PERISCOPE
TERMINATION
11
3.3.2 CORNER
TERMINATION
11
3.4 VENT
TERMINAL
CLEARANCES
12
3.5
VENT APPLICATION FLOW CHART
13
3.6 DEFINITIONS
13
3.7
ELBOW VENT LENGTH VALUES
14
3.8
TOP EXIT HORIZONTAL TERMINATION
14
3.9
REAR EXIT HORIZONTAL TERMINATION
16
3.10
TOP OR REAR EXIT VERTICAL TERMINATION
18
4.0 PRE-INSTALLATION
PREPARATION
21
4.1 DOOR
OPERATION
21
4.2 REAR
EXIT
21
4.3 TOP
VENT
21
5.0 INSTALLATION
22
5.1
WALL AND CEILING PROTECTION
22
5.2 HORIZONTAL
INSTALLATION
23
5.3 VERTICAL
INSTALLATION
23
5.4
USING FLEXIBLE VENT COMPONENTS
24
5.4.1 HORIZONTAL
AIR
TERMINAL
INSTALLATION
24
5.4.2 VERTICAL
AIR
TERMINAL
INSTALLATION
25
5.5.3
APPLIANCE VENT CONNECTION
26
5.5
USING RIGID VENT COMPONENTS
26
5.5.1 HORIZONTAL
AIR
TERMINAL
INSTALLATION
26
5.5.2
EXTENDED HORIZONTAL AND CORNER TERMINAL INSTALLATION
26
5.5.4 VERTICAL
AIR
TERMINAL
INSTALLATION
27
5.6
VERTICAL THROUGH EXISTING CHIMNEY
28
5.7
MOBILE HOME INSTALLATION
29
5.8 GAS
INSTALLATION
29
5.9
OPTIONAL WALL SWITCH EXCLUDING BCDV36CFG
30
6.0 FRAMING
31
6.1 INSTALLING
STAND-OFFS
32
6.2
MINIMUM FRAMING DIMENSIONS
33
6.2.1
STEEL HEADER INSTALLATION FOR CLEAN FACE AND CRYSTALLO SURROUNDS
34
6.3
MINIMUM ENCLOSURE CLEARANCES
35
6.3.1
REAR VENT ENCLOSURE
35
6.3.2
TOP VENT ENCLOSURE
36
6.3.3
FINISHED FLOOR INSTALLATION
37
6.3.4 HEARTH
INSTALLATION
37
6.4
NON-COMBUSTIBLE FACING MATERIAL
38
6.5 ALCOVE
FRAMING
38
6.6
REMOTE RECEIVER PLACEMENT
39
6.7
MINIMUM MANTEL CLEARANCES
39
7.0 FINISHING
40
7.1
SAFETY SCREEN & DOOR INSTALLATION / REMOVAL
40
7.2
CLEAN FACE TRIM KIT INSTALLATION
41
7.3 LOGO
PLACEMENT
42
7.4
OPTIONAL ROCK KIT
42
8.0 FINISHING
43
8.1
GLASS BURNER INSTALLATION
43
9.0 WIRING
DIAGRAM
44
9.1 LIGHT
SWITCH
44
9.2 BURNER
SWITCH
45
9.3
RECEPTACLE WIRING DIAGRAM
46
10.0 OPERATION
46
10.1 LIGHT
OPERATION
46
10.2 BCDV36CF
47
10.3 BCDV36CFG
48
11.0 ADJUSTMENTS
49
11.1 PILOT
BURNER
ADJUSTMENT
49
11.2 VENTURI
ADJUSTMENT
49
11.2.1 BCDV36CF
VENTURI
ADJUSTMENT
49
11.3
BCDV36CFG FLAME CHARACTERISTICS
50
11.3.1 BCDV36CFG VENTURI ADJUSTMENT
50
11.4 FLAME
CHARACTERISTICS
51
12.0 MAINTENANCE
51
12.1 ANNUAL
MAINTENANCE
52
12.2 LED
ASSEMBLY
REPLACEMENT
53
