background image

 

 

 

c. Use Button Backup Function   

When you press the “

Backup Button”

 in front of the X-Rev, the 

Button Manager utility 

will 

do the backup as a preset task. 

 

 

 

„

 

Indicator Descriptions

 

       

 

 

HDD

 

 

:

 Hard Disk Drive data access indicator   

This

 

indicator will turn flash while data is reading or writing between PC and 

X-Rev 

Storage Center

 

Note: 

Some

 

new SATA hard drive do not support data access display. 

 

 

„

 

Notes for user application 

-------------------------------------------------------------------------------------------------------------------------------

 

USB and eSATA port Priority 

    The 

X-Rev Storage Center

 provides dual interface of USB and eSATA for host connectivity, but the 

high-speed eSATA port will have priority over the USB port when both are connected at the same time.   

------------------------------------------------------------------------------------------------------------------------------

 

How to identify SATA and eSATA connectors

 

It is possible to have two types of SATA connector in your computer. One is a SATA type-A connector for 
internal ports. This usually connects to internal SATA hard drives by a standard SATA cable. All internal 
connections are Type A and have a “L” key to ensure the correct orientation. 
 
The other is an eSATA connector that does not have 
the “L” shaped key. It is usually used for external 
SATA device connection. An eSATA cable is needed 
to connect these external SATA devices. The X-Rev 
Storage Center connects via this eSATA connection. 
 
The eSATA cable supports both the high-speed SATA 
II at 3 Gb/sec and the SATA I at 1.5 Gb/sec. The 
picture on the right will help you recognize the 
different plugs between standard SATA and eSATA. 

------------------------------------------------------------------------------------------------------------------------------

 

   

X-Rev Storage Center housing temperature 

Usually the aluminum housing temperature will remain at around 30

°

C after working for a couple of 

hours. This is due to the heat sink design and is not a malfunction.

 

-------------------------------------------------------------------------------------------------------------------------------

 

Summary of Contents for X-Rev Storage Center


















Reviews: