background image

Error Message Resolution Guide 

 

Message 

Reason 

Solution 

Reference Tech Note 

 

 

 

 

INVALID KEY; 

The key pressed is not valid. 

Ensure that you are entering input into the 
correct field. 

--- 

MUST CLEAR FIELD; 

Trying to enter data in a field that 
must be cleared first. 

Ensure that you are entering input into the 
correct field. 

--- 

SCAN NOT ALLOWED; 

Trying to scan into a key only field. Ensure that you are entering input into the 

correct field. 

--- 

KEY NOT ALLOWED; 

Trying to key into a scan only field. Ensure that you are entering input into the 

correct field. 

--- 

ENTRY TOO SHORT; 

Trying to exit the field before it is 
filled. 

Ensure that you are entering input into the 
correct field. 

--- 

RECOVERABLE ERROR; 

Encountered an error from which 
you can continue. 

Verify that your configuration settings for the 
hardware being used, usually a printer and 
cable issue. 

--- 

UNRECOVERABLE ERROR; 

Encountered an error from which 
you can NOT continue. 

Verify that your Network settings are correct 
and you are in the correct mode using the 
correct Port. 
 

T1113, T1114, T1161, 
T1171, T1187 and 
T1194 

FUNCTION: \n\nFILE: \nLINE: \nCODE; Encountered an error from which 

you can NOT continue. 

Notify Connect over the web incident 
reporting system. 

--- 

Press any key\nFor More Details...; 

Press Enter for more information.  Advisory message. 

--- 

Press any key; 

Press a key to continue. 

Advisory message. 

--- 

 

 

Supported Equipment Manual 

   

   May, 2006 

4-2

Summary of Contents for Datalogic Formula 7400













































































Reviews: