Connect Tech Multi-I/O User Manual Download Page 28

Page: 28 / 50

Connect Tech - Xtreme/Multi-I/O - Users Guide

Document: CTIM-00116
Revision: 0.02

0.02

Page 28 of 50

Connect Tech Inc. Proprietary Information

Date: Apr. 14, 2015

Board Control/Status Registers

Implemented in the FPGA is 2 registers which assist with the operation of the board. The Base PC/104
IO-Address for these registers is defined by the

BP=

command.

Register

Function

IO Offset

INTR_STAT

Interrupt Status

0x00 (read-only)

RESET_CONT Reset Control

0x00 (write-only)

LED_CONT

LED Control

0x01 (write-read)

INTR_STAT Register (Offset 0x00, read-only)

Software can use the

Interrupt Status

“active-high”.

Control Item

Bit

Offset

Bit

Value

Comment(s)

Uart Group-1

0x1 Uart Ports 1 through 4 interrupt is active

Uart Group-2

0x2 Uart Ports 5 through 8 interrupt is active

CAN Port-1

0x4 CAN Port 1 interrupt is active

CAN Port-2

0x8 CAN Port 2 interrupt is active

J1708 Port

0x10 J1708 Port interrupt is active

Unused



Reserved for future use

RESET_CONT Register (Offset 0x00, write-only)

Software can use the

Miscellaneous Control

respective bit, will

hold

the reset on the respective circuit.

Control Item

Bit

Offset

Bit

Value

Comment(s)

PIC32_RST

0x1 PIC32 Microcontroller Reset

Uart Group-1_RST

0x2 Uart Ports 1 through 4 reset

Uart Group-2_RST

0x4 Uart Ports 5 through 8 reset

CAN Port-1_RST

0x8 CAN Port 1 reset

CAN Port-1_RST

0x10 CAN Port 2 reset

Module-1_RST

0x20 MultiTech Module-1 reset

Module-2_RST

0x40 MultiTech Module-2 reset

BUS_TEST

0x80 PC104 Address Bus test mode enable

PC104 Bus Test

This bit enables a mode where the PC104 Address Bus signals can be confirmed as functioning. This bit
should be set to zero for normal operation of the board.

Summary of Contents for Multi-I/O



















































Search results

Summary of Contents for Multi-I/O

Reviews:

Related manuals for Multi-I/O

Brands by name

Popular brands

Connect Tech Multi-I/O, User Manual

Search results

Summary of Contents for Multi-I/O

Reviews:

Related manuals for Multi-I/O

Brands by name

Popular brands