Condux CableGlider User Manual And Safety Manual Download Page 2

Page: 2 / 25

Important Safety Notice

Read and understand all procedure and safety instructions before using a Condux Fiber Optic Cable Puller.

Observe all safety information on this page and note specific safety requirements as explained by procedures

called out in this manual. Failure to follow these instructions could result in serious personal injury or death.

If you have questions on:

SAFETY - OPERATIONS - APPLICATIONS

CALL 1-800-533-2077

ADVERTENCIA:

Favor de leer y comprender todas las instrucciones de operación y seguridad antes de usar la máquina. Si Ud.

no comprende las instrucciones favor de consultarle a su jefe.

READ MANUAL

FIRST

WEAR

HARD HAT

WEAR SAFETY

GLASSES

WEAR SAFETY

SHOES

WEAR SAFETY

GLOVES

Save this user’s guide for future reference.

Summary of Contents for CableGlider


























Search results

Summary of Contents for CableGlider

Reviews:

Related manuals for CableGlider

Brands by name

Popular brands

Condux CableGlider, User Manual And Safety Manual

Search results

Summary of Contents for CableGlider

Reviews:

Related manuals for CableGlider

Brands by name

Popular brands