Condux CableGlider User Manual And Safety Manual Download Page 6 | Manualshive

Page: 6 / 25

background image

6

Unpacking the Fiber Optic Cable

Puller

A. PULLER COMPONENTS

1. Fiber Optic Cable Puller Package 1

Part Number:

08690001

• Hydraulic puller mounted on a 2

1

⁄

2

inch (64 mm) square tube

• Foot control valve assembly

• Hydraulic hoses from puller to foot control valve assembly (10 foot)

• Hydraulic hoses from foot control valve assembly to power supply (20 foot)

• Owner’s manual

• Shipping crate

2. Fiber Optic Cable Puller Package 3

Part Number:

08690055

All Items in Package 1 Plus:

• Electronic load cell mounted on puller

• Electronic control box with digital chart recorder

• Electronic cord from control box to puller

• Electronic cord from control box to foot control valve assembly

• Power cord, vehicle’s power point to control box

!NOTE:

If any parts are missing, please contact your Condux representative or call

Condux International at 1-800-533-2077.

4.

«
...
4
5
6
7
8
...
»

Summary of Contents for CableGlider


























Reviews:

No comments

Related manuals for CableGlider

Brand: ACS Pages: 56

Brand: Hagie Pages: 61

Brand: JackJaw Pages: 2

Brand: Ecco Pages: 3

Brand: Ecco Pages: 2

Brand: Landoll Pages: 94

Brand: Bang & Olufsen Pages: 2

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brand: Pablo Pages: 7

Brand: Tascam Pages: 8

Brand: Nabtesco Pages: 26

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands