background image

TROUBLESHOOTING

Iron does not heat

• Make sure that the iron is plugged in and turned on. Make sure

to select a fabric.

• The automatic  shutoff may have activated: Move the iron to reset

and begin heating.

Iron does not steam

• The iron will only produce steam at the highest settings (Wool,

Cotton, Linen). Make sure the iron is set to one of those.

• The variable steam control must not be set to the “no steam“ setting.

Move the variable steam control to one of the steam settings.

• Make sure the water tank is full.

• After many months of use in a very hard water environment, the

steam chamber can become clogged with hard mineral deposits,

which may block steam production. Follow the self-clean procedure

to eliminate some of the deposits from the steam chamber. 

Water leaks from the soleplate

• Make sure that you are using the Burst of Steam in the higher 

settings, If not, the iron will not be hot enough to produce steam.

• When storing the iron turn the variable steam knob to “no steam”

setting. Try to store the iron sitting on the heel rest.

Iron is flashing and beeping

• Unplug and inspect for damage

• If there is no damage, plug iron in and iron will operate normally.

8. After 30 seconds of Self Clean activation, release the Self Clean

control and place iron on its heel rest.

9. Unplug iron.

10. With a clean soft cloth, wipe soleplate clean of water and

flushed deposits.

Before reusing iron after Self Clean Procedure:

1. Refill water tank

2. Set iron to maximum. When it is ready, operate Burst of Steam

to flush any remaining deposits out of the soleplate.

Automatic Shutoff

This iron is equipped with an automatic shutoff circuit that will shut

down the heater if the iron is left motionless in the following posi-

tions for the following time: Heel rest: 10 minutes; face down: 30

seconds; on its side: 30 seconds.

When the automatic shutoff has been triggered, the Auto Shutoff

Indicator will appear in the display. To restart the iron, move it back

and forth. The iron will heat up to the last setting.

If the iron has been knocked off the pressing surface to the floor, the

impact sensor will shut the iron off immediately. If there is no dam-

age, plug in iron and it will function normally.

WARNING

If the iron has been dropped, unplug the iron

and inspect it for damage. If there is obvious damage or if you hear

any loose parts or suspect the iron has been damaged, contact

Conair Customer Service at 1-800-472-7606 to arrange for serv-

ice. Be extremely cautious if you have dropped the iron. Until

unplugged  exposed electrical components could cause an electric

shock, serious injury or death.

05CN1258 DPP3000C IB  11/17/05  11:52 AM  Page 10

Summary of Contents for DPP3000 Series













Reviews: