Comtech EF Data CRS-180 Installation And Operation Manual Download Page 83

Page: 83 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Cables and Connections

Revision 11

5–25

5.4 Cabling to the CDM-570 or CDM-570A

For information on the CDM-570/A’s 1:1 auto-enable functionality, see:

•

Chapter 4. MODEM

AND

SWITCH

CONFIGURATION

•

CDM-570/CDM-570L/CDMR-570L Satellite Modem Installation and

Operation Manual (CEFD P/N MN/CDM570L.IOM)

•

CDM-570A/CDM-570AL/CDMR-570AL Satellite Modem Installation and

Operation Manual (CEFD P/N MN-CDM570A)

For information on the cables and cable assemblies specified in this section, see

Appendix A. CABLE DRAWINGS

5.4.1 CRS-180



CDM-570/A Control and IF Interface Connections Using

Cabling Kit KT/11599

You must use the Comtech EF Data KT/11599 1:1 Redundancy Control/IF Interface Cabling Kit

for all possible CDM-570/A NON-IP data interface configurations:

KT/11559 1:1 Redundancy Control/IF Interface Cabling Kit (CRS-180



CDM-570/A)

CEFD P/N

Qty/Kit

(REF) Description

Used For

Ch. 5

Fig

PL/11560-1

CRS-180 Switch – Top Assembly

1:1 Redundancy

5-36

5-37

PL/0946-1

IF (Tx/Rx) Coax Cable, 50Ω Type ‘BNC’, 4’

Modem



Switch IF

Interface

5-37

CA/WR9378-4*

Control Cable – Universal, DB-9M



DB-9M, 4’

Modem



Switch

Control

5-36

XF/BNC-MF-50-75

Transformer, 50-75

Ω

, 2-200 MHz, BNC, M/F

User IF Tx/Rx

Interface

5-37

CA/RB10461-1

Cable – 1:1 Y-Splitter, (2X) DB-25M



DB-25F

EIA-422/232

Interface

5-39

CA/WR10522-1

Cable – 1:1 Y-Splitter, (2X) DB-15M



DB-15F

G.703 Balanced

5-40

KT/10553-1

G.703 Unbalanced Interface Kit containing:

(Qty 4) CA/BNC75OHM Cable – IF BNC, 1’

(Qty 2) CN/BNC-Tee-JPJ T-Adapter, 50Ω BNC

G.703 Unbalanced

5-41

* Alternate Cabling Note – CEFD Universal Control Cable CA/WR9378-8 (DB-9M



DB-9M, 8’), sold separately, is available for use in place of CA/WR9378-4

Figure 5-22 and Figure 5-23 show how to connect a pair of CDM-570/A modems together with

the CRS-180; the table for each figure lists the cable assemblies provided in the KT/11559 kit for

this initial setup. See Sect. 5.4.1.1 for the CDM-570/A Modem-to-Switch Control Interface

connection, and Sect. 5.4.1.2 for the CDM-570/A Modem-to-Switch IF Interface connection.

Summary of Contents for CRS-180






































































































































Search results

Summary of Contents for CRS-180

Reviews:

Comtech EF Data CRS-180, Installation And Operation Manual, Page: 83 / 134

Search results

Summary of Contents for CRS-180

Reviews: