manualshive.com logo in svg

Comtech EF Data CRS-180, Installation And Operation Manual, Page: 14 / 134

Share
Download
Comtech EF Data CRS-180 Installation And Operation Manual Download Page 14

CRS-180 70/140 MHz IF 1:1 Redundancy Switch  

MN/CRS180.IOM 

Preface 

Revision 11 

xiv 

Equipment Connection 

 

 

THE CRS-180 IS DESIGNED FOR OPERATION  ONLY  WITH THE COMTECH EF DATA 

PRODUCTS LISTED IN THIS MANUAL UNDER ‘RELATED DOCUMENTS’. THESE 

PRODUCTS SUPPLY DC OPERATING CURRENT (ELECTRONICALLY FUSED AND 

PROTECTED) AND CONTROL SIGNALS FOR THE CORRECT FUNCTIONING OF THIS 

SWITCH. CONNECTION TO OTHER MANUFACTURERS’ EQUIPMENT COULD RESULT 

IN DAMAGE TO THE SWITCH. THE CRS-180 IS NOT COMPATIBLE WITH OTHER 

COMTECH EF DATA MODEMS OR PRODUCTS NOT LISTED IN THIS MANUAL. 

European Union Radio Equipment and Telecommunications Terminal 

Equipment (R&TTE) Directive (1999/5/EC) and EN 301 489-1 

Independent testing verifies that the unit complies with the European Union R&TTE Directive, its 

reference to EN 301 489-1 (

E

lectromagnetic compatibility and 

R

adio spectrum 

M

atters [ERM]; 

E

lectro

M

agnetic 

C

ompatibility [EMC] standard for radio equipment and services, Part 1: 

Common technical requirements)

, and the Declarations of Conformity for the applicable 

directives, standards, and practices that follow: 

European Union Electromagnetic Compatibility (EMC) Directive 

(2004/108/EC) 

•

 

Emissions: EN 55022 Class A – Limits and Methods of Measurement of Radio Interference 

Characteristics of Information Technology Equipment. 

 

•

 

Immunity: EN 55024 – Information Technology Equipment: Immunity Characteristics, Limits, 

and Methods of Measurement. 

 

•

 

EN 61000-3-2 – Harmonic Currents Emission 

 

•

 

EN 61000-3-3 – Voltage Fluctuations and Flicker. 

 

•

 

Federal Communications Commission Federal Code of Regulation FCC Part 15, Subpart B.  

 

 

CAUTION – TO ENSURE THAT THE UNIT COMPLIES WITH THESE STANDARDS, OBEY 

THESE INSTRUCTIONS: 

•

 

Use coaxial cable that is of good quality for connections to the L-Band Type ‘N’ Rx (receive) 

female connector. 

 

•

 

Use Type 'D' connectors that have back-shells with continuous metallic shielding. 

 

•

 

Type ‘D’ cabling must have a continuous outer shield (either foil or braid, or both). The 

shield must be bonded to the back-shell. 

 

•

 

Operate the Switch and modems with their covers on at all times.   

Summary of Contents for CRS-180







































































































































Reviews:

No comments