Comtech EF Data CRS-180 Installation And Operation Manual Download Page 6

Page: 6 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Table of Contents

Revision 11

5.4

Cabling to the CDM-570 or CDM-570A .............................................................................. 5–25

5.4.1 CRS-180



CDM-570/A Control and IF Interface Connections Using Cabling Kit KT/11599 .. 5–25

5.4.1.1

Switch-to-Modem Control Interface Connection ......................................................... 5–26

5.4.1.2

Switch-to-Modem IF Interface Connection .................................................................. 5–27

5.4.2 Modem-to-User Data Interface Connections and Examples ................................................. 5–28

5.4.2.1.1 EIA-422/232 Interface Example .............................................................................. 5–29

5.4.2.1.2 G.703 Balanced Interface Example ......................................................................... 5–29

5.4.2.1.3 G.703 Unbalanced Interface Example .................................................................... 5–30

5.4.2.2

Modem-to-User IP (10/100 Ethernet) Interface Example ............................................ 5–31

5.5

Cabling to the CDM-710G ................................................................................................. 5–33

5.5.1 CRS-180



CDM-710G Control and IF Interface Connections Using Cabling Kit KT/12554 ... 5–33

5.5.2 Modem-to-User Data Interface Kit and Connection Examples ............................................. 5–35

5.5.2.1.1 Single G.703 E3/T3/STS-1 75

Ω

Data Interface (CDI-10-1) Kit KT/12583 ................ 5–36

5.5.2.1.2 HSSI Data Interface (CDI-60) Kit KT/12586 ............................................................. 5–37

5.5.2.2

Gigabit Ethernet Interface (CDI-70) Example ............................................................... 5–38

5.6

Cabling to the CDM-710 ................................................................................................... 5–39

5.6.1 CRS-180



CDM-710 Control and IF Interface Connections Using Cabling Kit KT/12551 .... 5–39

5.6.2 Modem-to-User Data Interface Kit and Connection Examples ............................................. 5–41

5.6.2.1.1 ASI 75Ω Data Interface (CDI-40) Kit KT/12579 ....................................................... 5–42

5.6.2.1.2 HSSI Data Interface (CDI-60) Interface Kit KT/12578 .............................................. 5–43

5.6.2.2

Gigabit Ethernet Data Interface (CDI-70) Example ....................................................... 5–44

5.7

Cabling to the CDM-700 ................................................................................................... 5–45

5.7.2 Modem-to-User Data Interface Kit and Connection Examples ............................................. 5–47

5.7.2.1

Modem-to-User Non-IP Data Interface Kit and Connection ......................................... 5–47

5.7.2.1.1 Dual G.703 E3/T3/STS-1 75

Ω

Data Interface (CDI-10) Kit KT/12542 and HSSI Data

Interface (CDI-60) Kit KT/12578 ................................................................................................. 5–48

5.7.2.1.2 155MB Copper Data Interface (CDI-50) Kit KT/12579 ............................................ 5–49

5.7.2.1.3 OC-3 Data Interface (CDI-50) Kits KT/12580 (Single-Mode) or KT/12581 (Multi-Mode)

................................................................................................................................ 5–50

5.7.2.2

Gigabit Ethernet Data Interface (CDI-70) Example ....................................................... 5–51

APPENDIX A.

CABLE DRAWINGS ......................................................................... A-1

A.1

Overview ........................................................................................................................... A-1

A.2

Control Interface Cables ..................................................................................................... A-2

A.2.1

Switch-to-Modem, Universal Control Cable, DB-9M



DB-9M ........................................... A-3

A.2.2

Switch-to-Modem, Adapter Control Cable, RoHS, DB-9M



DB-15F .................................. A-4

A.2.3

Switch-to-Modem, Optional ‘Y’ Splitter Adapter Control Cable, (2X) DB-9M



DB-15F ..... A-5

A.2.4

Switch-to-Modem, Optional Control Cable, Non-muting, DB-9M



DB-15F ...................... A-6

A.3

IF / Data Interface Cables ................................................................................................... A-7

A.3.1

Switch-to-Modem / Modem-to-User, Coaxial Cable, RoHS, BNC 50Ω ................................ A-9

A.3.2

Switch-to-Modem / Modem-to-User, Coaxial Cable, RoHS, BNC 75Ω .............................. A-10

Summary of Contents for CRS-180






































































































































Search results

Summary of Contents for CRS-180

Reviews:

Comtech EF Data CRS-180, Installation And Operation Manual, Page: 6 / 134

Search results

Summary of Contents for CRS-180

Reviews: