Comtech EF Data CRS-180 Installation And Operation Manual Download Page 20

Page: 20 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Introduction

Revision 11

1–2

Table 1-1. CRS-180 Compatibility Summary

Modem

1:1 Data Switch

Firmware/Hardware Requirement*

CDM-625/A

Built into the CDM-625/A

Firmware Ver. 1.1.1 or higher

CDM-760

Built into the CDM-760

Firmware Ver. 1.1.1 or higher

CDM-750

Built into the CDM-750

Firmware Ver. 1.1.1 or higher

CDM-570A

Built into the CDM-570A

Firmware Ver. 1.1.1 or higher

CDM-570A with Optional IP Packet

Processor

User-provided Layer 2 switch or hub

Firmware Ver. 1.2.1 or higher

CDM-570

Built into the CDM-570

•

Firmware Ver. 1.6.7 or higher

•

Hardware Revision 3

CDM-570 with Optional IP Module

User-provided Layer 2 switch or hub Firmware Ver. 1.5.4.2 or higher

CDM-710G

Built into the CDM-710G

Firmware Ver. 5.1.1 or higher

CDM-710

Built into the CDM-710

•

Firmware Ver. 2.4.1 or higher

•

Hardware Revision 3

CDM-700

Built into the CDM-700

•

Firmware Ver. 1.1.6 or higher

•

Hardware Revision 3

* Firmware updates are free and may be downloaded from the Comtech EF Data web site

(http://www.comtechefdata.com). If a modem does not meet the hardware requirements,

contact Comtech EF Data Product Support. Hardware revision upgrades must be performed

at CEFD.

1.2 Physical Features

1.2.1 Modem Side Features

Figure 1-2 shows the modem side of the CRS-180. The connectors provided here facilitate all

necessary external connections between the CRS-180 and the compatible Comtech EF Data

modems.

Tx B

Tx A

Control A

Control B

Rx B

Rx A

Ref Des

Name

Connector Type

Function

Chapter Sect.

Rx A

BNC

IF Input to Modem ‘A’

3.2.1.1

Rx B

BNC

IF Input to Modem ‘B’

3.2.1.1

Control A

DB-9F 9-pin Type ‘D’ female Modem ‘A’ Control Interface

3.2.1.2

Control B

DB-9F 9-pin Type ‘D’ female Modem ‘B’ Control Interface

3.2.1.3

Tx A

BNC

IF Output from Modem ‘A’

3.2.1.1

Tx B

BNC

IF Output from Modem ‘B’

3.2.1.1

Figure 1-2. CRS-180 – Modem Side Features

Summary of Contents for CRS-180






































































































































Search results

Summary of Contents for CRS-180

Reviews:

Comtech EF Data CRS-180, Installation And Operation Manual, Page: 20 / 134

Search results

Summary of Contents for CRS-180

Reviews: