Comtech EF Data CRS-180 Installation And Operation Manual Download Page 47

Page: 47 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Modem and Switch Configuration

Revision 11

4–7

4.3 CDM-760 or CDM-750 Operation in 1:1 Redundancy

•

CDM-760 Advanced High-Speed Trunking Modem Installation and Operation

Manual (CEFD P/N MN-CDM760)

•

CDM-750 Advanced High-Speed Trunking Modem Installation and Operation

Manual (CEFD P/N MN-CDM750)

The CDM-760 and CDM-750 Advanced High-Speed Trunking Modems automatically detect

connection to a 1:1 redundancy system. Typical for either product, with both modems

automatically configured for 1:1 operation, the online modem keeps the offline modem

updated as online modem configuration changes occur.

You can also manually ‘force’ backup of the online modem. Use the modem front panel to

select the

Utility



1:1

screen:

Press ENTER key to force Unit into
Standby (1:1 only)

If the unit is part of a 1:1 redundant pair and this unit is currently

online

, press ENTER to force

the current unit to switch to standby mode.

Summary of Contents for CRS-180






































































































































Search results

Summary of Contents for CRS-180

Reviews:

Comtech EF Data CRS-180, Installation And Operation Manual, Page: 47 / 134

Search results

Summary of Contents for CRS-180

Reviews: