manualshive.com logo in svg

CompUSA 333628, User Manual

Share
Download
CompUSA 333628 User Manual Download Page 2

 

1

FCC and CE Radiation Norm 

 

FCC 
 

This equipment has been tested and found to comply with limits for Class B digital device pursuant 
to Part 15 of Federal Communications Commission (FCC) rules.  
 

CE 
 

This equipment has been tested and found to comply with the limits of the European Council 
Directive on the approximation of the law of the member states relating to electromagnetic 
compatibility (89/336/EEC) according to EN 55022 Class B. 
 

FCC and CE Compliance Statement 

 
These limits are designed to provide reasonable protection against frequency interference in 
residential installation. This equipment generates, uses and can radiate radio frequency energy, 
and if not installed or used in accordance with the instructions, may cause harmful interference to 
radio communication. However, there is no guarantee that interference will not occur in television 
reception, which can be determined by turning the equipment off and on. The user is encouraged 
to try and correct the interference by one or more of the following measures: 
 

ƒ

  Reorient or relocate the receiving antenna 

ƒ

  Increase the separation between the equipment and the receiver 

ƒ

  Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected to. 

 

          

 

 
 

CAUTION! 
 

The Federal Communications Commission warns the user that changes or modifications to the 
unit not expressly approved by the party responsible for compliance could void the user’s authority 
to operate the equipment.

 

Summary of Contents for 333628







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands