ComAp IG-NT GC Reference Manual Download

Page: 168 / 260

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

168

Group: Load shedding

Value: StatLdShed

Group

Load shedding

Units

Related FW

3.0

Description

The value indicates the current load shedding stage. 0 indicates that the load
shedding is not active. See the chapter

Load shedding

for more details.

Group: Analog CU

Value: UBat

Group

Analog CU

Units

Related FW

3.0

Description

Voltage at the controller power supply terminals.

Value: CPU Temp

Group

Analog CU

Units

ºC

Related FW

3.0

Description

Temperature inside the controller (on the CPU).

Value: D+

Group

Analog CU

Units

Related FW

3.0

Description

Voltage measured at the D+ terminal. If this voltage is > 80% of the

Ubat

the D+

terminal is evaluated as active and the engine is evaluated as running. See also
the chapter

Start sequence

Value: AIN CU-1

Group

Analog CU

Units

configurable

Related FW

3.0

Description

This is the value of the analog input 1 of the controller. Analog inputs are fully
configurable so the name and units depend on configuration. In the default
configuration the input is used for oil pressure measurement.

Summary of Contents for IG-NT GC





































































































































































































































































Search results

Summary of Contents for IG-NT GC

Reviews:

Related manuals for IG-NT GC

Brands by name

Popular brands

ComAp IG-NT GC, Reference Manual

Search results

Summary of Contents for IG-NT GC

Reviews:

Related manuals for IG-NT GC

Brands by name

Popular brands