Colortrac SingleSensor CIS Instruction Manual Download Page 6 | Manualshive

Page: 6 / 23

background image

SC Scanner Instruction Manual

Page 6 of 23

5. Close the Lid Assembly

making sure both Lid Latches
lock securely.

6. Carefully lift the Top Lid

Cover off from the Lid
Assembly.

7. Remove the Aluminium EMC

Tape covering the cables to
the Main Board.

8. Remove the 4 x M3 screws

holding the Main Board
Cover to the Lid Assembly.

«
...
4
5
6
7
8
...
»

Summary of Contents for SingleSensor CIS
























Reviews:

No comments

Related manuals for SingleSensor CIS

Brand: Dacor Pages: 4

Brand: Vaisala Pages: 24

Brand: Yakima Pages: 8

Brand: Abicor Binzel Pages: 44

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Brand: YachtSafe Pages: 2

Brand: 4 tec SENSORTECHNOLOGY Pages: 5

Brand: HBX Pages: 12

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Brand: Havis-Shields Pages: 3

Brand: Beurer Pages: 36

Brand: Webasto Pages: 34

Brand: LAZER Pages: 19

Brand: Kong Pages: 72

Brand: Keith Pages: 44

Brand: Raceface Pages: 9

Brand: Nolan Pages: 24

Brand: Milesight Pages: 27

Brand: Simplicity Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands