manualshive.com logo in svg

Color Kinetics LL011L360WW120000, Maintenance Manual

Share
Download
Color Kinetics LL011L360WW120000 Maintenance Manual Download Page 36

36

  Chapter 5

C

 Important

Be careful with the use of 
solvents like benzene, xylol and 
acetone because these might 
damage the fabric.

E

 Tip

These tips for stain removal are 
only recommendations. 100% 
removal is not guaranteed!
In all cases it is recommended to 
obtain specialist advice from a 
reputable dry cleaner.

5 

Care instructions 

for the textile finish

Stains can often be removed using a damp cloth before they penetrate 
the fibers.

If the stain has dried, first scrape off as much as possible with a brush 
and remove as much as possible with a vacuum cleaner. Avoid the 
use of any liquids apart from what is advised in section 

5.2 Detailed 

cleaning instructions

.

5.1  Material specification: Trevira CS

All textile finishes of the luminous textile are made from Trevira CS yarns.

Trevira CS is a special type of polyester (synthetic fiber): the chemical 
composition of the fibers makes this textile permanently flame-retardant. 
This quality remains intact after repeated laundering and long-term usage. 

5.2  Detailed cleaning instructions

Pollution

Solution

Ballpoint pen

Use surgical spirit, then acetone (for example oil-free nail varnish remover). It is 
recommended that after every cleaning, spray extraction is used, so that any edge marks 
or residual cleaning agents are removed.

Chocolate

Treat fresh stains with an alkaline-based cleaning agent (for example soap flakes 
or washing-up liquid and soda). It is recommended that after every cleaning, spray 
extraction is used, so that any edge marks or residual cleaning agents are removed.

Ink

Treat using water mixed with furniture shampoo. It is recommended that after every 
cleaning, spray extraction is used, so that any edge marks or residual cleaning agents 
are removed.

Paint (water-based)

Start with just cold water. Then use water mixed with furniture shampoo. Finally, contact 
a specialist. It is recommended that after every cleaning, spray extraction is used, so that 
any edge marks or residual cleaning agents are removed.

Alcohol, black coffee, jelly, 
juice, fruit and syrup-based 
drinks, tea, wine

Treat fresh stains with a weak solution of organic acids (household vinegar). Rinse 
immediately. Treat dried stains treat with a general “oxidative” bleaching agent, for 
instance a 3% hydrogen peroxide solution. It is recommended that after every cleaning, 
spray extraction is used, so that any edge marks or residual cleaning agents are removed.

Blood, cream, gravy, milk, 
urine, vomit

Treat fresh stains with an alkaline-based cleaning agent (for example soap flakes 
or washing-up liquid and soda). It is recommended that after every cleaning, spray 
extraction is used, so that any edge marks or residual cleaning agents are removed.

Butter, candle wax, chewing 
gum, grease, lipstick, nail 
varnish, oil, oil-based paint, 
shoe polish, soot

Treat with a solvent (benzene, xylol, acetone etc. It is recommended that after every 
cleaning, spray extraction is used, so that any edge marks or residual cleaning agents 
are removed.

5

Summary of Contents for LL011L360WW120000











































Reviews:

No comments

Brands by name

Popular brands

Load more brands