manualshive.com logo in svg

Coloelite UC-711 E, Operation Manual

Share
Download
Coloelite UC-711 E Operation Manual Download Page 24

24

Part VI – Starting the Freezer

Only after completing the cleaning and sanitizing
procedures should you fill the machine with fresh
mix. The mix being used 

MUST

 be free of ice,

seeds, pulp, and completely dissolved if made from
powder. The products used in these freezers must be
a homogenous liquid.

A) Gravity Fed Machine

The cylinder of this freezer are designed to allow for
simple start up and minimal product loss due to
improper overrun.

Fill the mix tank with fresh liquid mix. The mix tank
has a maximum capacity of 10 quarts. The
minimum recommended mix quantity is 3 quarts.

Allow the cylinder to fill with mix. When the air
bubbles stop coming out of the cylinder feed hole,
mix has filled the cylinder to its maximum capacity.
Install the assembled gravity feed tube into the
cylinder feed holes. Set to the closed position
(bottom).

You may now start the freezing process by pressing the
“Select” button (#571.2) and selecting the Automatic
mode.

The initial freeze time is approximately 4-7 minutes. Do
not dispense product until the machine has cycled off.
Before dispensing product you must also open the outer
regulating sleeve on the feed tube. The draw rate, portion
size, and mix viscosity will determine the final regulating
sleeve setting. Our standard setting is 2 or 3 notches up
from the bottom. Adjust for your specific application.

571.2

L2

L3

Summary of Contents for UC-711 E




































Reviews:

No comments

Brands by name

Popular brands

Load more brands