background image

3. SAFETY INFORMATION.

This product has been designed for safe operation when used as detailed in accordance 
with the Manufacturer’s instructions. 

NOTE:

 Failure to use this equipment in accordance with the manufactures operating 

instructions may compromise your basic safety protection afforded by the equipment and 
may invalidate the warranty / guarantee. The warranty / guarantee does not cover 
damaged caused by faulty installation or misuse of the equipment. 

3.1. 

Prevention of Fire and Electric Shock. 

To prevent a risk of fire or electric shock, 

DO NOT

 open your product 

case without authorisation. Only qualified Service personnel should 
attempt to repair this product.   

Replace fuses only with the type as listed in section, ‘Technical 
Specifications and Parts and Accessories’ (See fuse type and rating). 

Ensure the Mains Power Supply conforms to rating found on the data 
plate located on the under-side of this product and that of your MC 
Controller. 

Never

 Operate this equipment without connection to earth / ground. 

Ensure the mains supply voltage is correctly earthed / grounded in 
accordance with current area legislation.  

3.2. 

General Safe Operating Practice. 

Always follow good laboratory practice when using this  
equipment. Give due recognition to your company’s safety and 
legislative health & safety procedures and all associated legislation 
applicable to your areas of operation. Check laboratory procedures for 
substances being heated and ensure all hazards (e.g. explosion, 
implosion or the release of toxic or flammable gases) that might arise 
have been suitably addressed before proceeding.  When heating 
certain substances the liberation of hazardous gases may require the 
use of a fume cupboard or other means of extraction.  

Ensure equipment is used on a clean, dry, non-combustible, solid work 
surface with at least 400mm suitable clearance all around from other 
equipment. 

It is recommended that suitable protective eye glasses and gloves be 
worn when using this product.

 

Do not

 touch the upper part of this product while in use. The surface 

temperature will burn. 

Do not

 position the product so that it is difficult to disconnect from the 

MC Controller / Power supply. 

Do not 

touch the heating element or any glass vessel whilst in use. 

5

Summary of Contents for Electrothermal BA6101





















Reviews: