background image

Do not 

lean or stretch over equipment when in use. 

Do not 

immerse unit in water or fluids.

 

Do not 

spill substances onto this product. If spillage does occur, 

disconnect unit from mains supply and follow instructions as detailed 
in Maintenance. (Section 9). 

Do not 

cover this product whilst in use. 

Do not

 block or obstruct 

ventilation slots / airways.

 

Do not 

leave this product switched on when not in use. 

Do not 

thermally insulate the exposed upper section of this product, 

as the insulation used may obstruct the convection cooling airways 
around the rim and cause the product to overheat. 

It is not recommended to leave any heating apparatus unattended 
during operation. 

Only use Original Equipment manufactures spares and accessories. 
Ref Section 10. 

The equipment is not spark, flame or explosion proof and has not been 
designed for use in hazardous areas in terms of BSEN 60079-
14:1997. Keep flammable, low flash point substances away from the 
apparatus. 

Do not

 operate or handle any part of the product with wet hands. 

It is recommended this product be used with a

n Electrothermal MC5 

Controller (Energy Regulator)

. However for high temperature use it

may be connected directly to the mains electricity supply. Extra safety 
care should be used. 

Keep the Mains cord and lead set away from the heating surface. 

6

Summary of Contents for Electrothermal BA6101





















Reviews: