manualshive.com logo in svg

COFFEtek VITRO S3, Technical Manual

Share
Download
COFFEtek VITRO S3 Technical Manual Download Page 36

COFFE

tek 

LTD

 

 

VITRO S3 

Revision 1 

28/02/2017 

36 

 

 

 

 

MDB SETTINGS 

Settings 

Description 

EXACT CHANGE LIMIT 

Limit of how much change it will pay out 

MAX CREDIT 

The maximum credit that can be accepted 

NORMAL COINS 

The coins accepted in normal mode. 0 is not accepted, 1 is accepted 

EXACT CHANGE COINS  The coins accepted in exact change mode. 0 is not accepted, 1 is accepted 

NORMAL BILLS 

The bills accepted in normal mode. 0 is not accepted, 1 is accepted 

EXACT CHANGE BILLS 

The bills accepted in exact change mode. 0 is not accepted, 1 is accepted 

MASK AUTO CONFIG 

Use this to make the Vitro and the coin mech communicate. 

CHANGER MODE 

Single Vend 

– Vends one drink then gives change. 

Multi Vend 

– Vends drinks up to the value of credit. Change is given when 

the reject button is pressed 

VEND BEFORE 
CHANGE 

If set on, will enforce a vend before change is given. If off, money can be 
returned without a drink being selected. 

VALIDATOR ESCROW 

Not used 

CLEAR RC 

Clears remaining credit 

MDB  CASHLESS  MAX 
TIMEOUT 

The  amount  of  time  the  Vitro  will  wait  for  confirmation  when  using  a 
cashless device such as a card reader. 

 

Summary of Contents for VITRO S3





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands