COFFEtek VITRO S3 Technical Manual Download Page 33

Page: 33 / 68

COFFEtek

LTD

28/02/2017

Revision 1

VITRO S3

audible.

LEVELS
RETRY

If set to 1 this will attempt to refill the tank when encountering a tank fill fault

QUICK DRINK
TEST

If set to 1 this will allow you to test a drink while in “select drink to modify” by pressing
the star key

RM
COMMANDS

Reserved for future use

DISABLE APP

Use this option to disable the Button Barrista APP

CODED
ACCESS

When set to 1, access to engineer's mode is protected by a code.

SCRN

SAVE

TIMOUT

This is the number of seconds before the screensaver becomes active.

SCREEN
SAVE MODE

This changes the behaviour of the screensaver. Options are SCROLLING TEXT,
DISPLAY LOW POWER and DISPLAY OFF

AINTENANCE

ETTINGS

41.

Settings

Description

MAX
BREWER
VENDS

80
This is the number of coffee vends until the machine inhibits the coffee vends.

BIN WT A

Weight of ingredients in canister A. Used when behaviour code is set on

INGRED

MONITOR

BIN WT B

Weight of ingredients in canister B. Used when behaviour code is set on

INGRED

MONITOR

BIN WT C

Weight of ingredients in canister C. Used when behaviour code is set on

INGRED

MONITOR

Summary of Contents for VITRO S3





































































Search results

Summary of Contents for VITRO S3

Reviews:

Related manuals for VITRO S3

Brands by name

Popular brands

COFFEtek VITRO S3, Technical Manual

Search results

Summary of Contents for VITRO S3

Reviews:

Related manuals for VITRO S3

Brands by name

Popular brands