background image

CAFÉ ELITE

4

GENERAL

   Read the user guide before using the machine.
   This guide contains important instructions for 

proper and safe use of the vending machine.

   Always keep this guide close at hand for future 

reference.

Introduction

Thank you for choosing a Café Elite vending machine. 

We hope you enjoy it !

   Never immerse the machine, plug or mains 

cable in water because there is a danger of 
electric shock. 

   The appliance is not intended for use by 

persons (including children) with reduced 
physical, sensory or mental capabilities, or 
lack of experience and knowledge, unless they 
have been given supervision or instruction 
concerning the use of the appliance by a person 
responsible for their safety.

   Children should be supervised to ensure they 

do not play with the appliance.

   Do not use the machine if the mains cable, plug 

is damaged or the machine has fallen down.

   If the mains cable is damaged it must be 

replaced by the manufacturer, service agent or 
similarly qualified persons in order to avoid a 
hazard.

   Only plug the machine into a properly installed 

earthed safety socket whose line voltage 
matches the technical data for the machine.

   Do not use the machine outdoors so it can be 

exposed to weather (rain, snow, frost). It will 
cause material damage to the machine.

   Do not try to open the machine or repair it in 

any way. To avoid danger only have the machine 
repaired in a technical workshop, Service 
Centre or by a qualified person.

   Remove the mains cable from the socket when 

the machine is not in use for longer periods. To 
do this, pull the plug not the cable.

   This appliance must be placed in a horizontal 

position which is resistant to any water that 
may leak.

  Place the machine out of the reach of children.
   Position the mains cable so that people cannot 

trip over it. Keep it away from sharp edges and 
heat sources.

   The new hose-sets supplied with this appliance 

are to be used, old hose-sets must not be re-
used.

   This appliance is not suitable for installation in 

an area where a water jet could be used.

   This appliance must not be cleaned by a water 

jet.

   This appliance is intended to be used in 

household and similar applications such as: 

 

-

 Staff kitchen areas in shops. 

 

-

  Offices and other commercial working 

environments. 

 

-

 On agricultural estates. 

 

-

  By clients in hotels, motels and other 

residential type environments. 

 

-

 Bed and breakfast type environments.

   For the optimal performance of the machine 

these parameters shall not be exceeded:

 

-

  Maximum permissible inlet water pressure : 

800KPa (8Bar)

 

 Minimum permissible inlet water pressure: 
200KPa (2Bar)

 

Maximum working temperature: 40°ºC

 

Minimum working temperature: 10°ºC

Warnings

Precautions

Intended use

Summary of Contents for CAFE ELITE

























































Reviews: