Coemar Reflection FullSpectrum Instruction Manual Download Page 23

English 

24 

 

 

Mechanical parts

 

Check the correct working of the mechanical parts and, if needed, replace them. Make sure the projector is not mechanically 
damaged. If necessary, replace the worn parts. 

Electrical components

 

Check all electrical connections, in particular for correct grounding and correct attachment of all extractable connectors. Press the 
connectors if necessary and reposition as before. 
 

11.3 Fuses: 

 
Reflection has an automatic fuse that in most cases does not need to be replaced. 

12. F.A.Q. and answers  

 
The following list shows common issues that may be simply solved. If issues persist, the unit must be repaired by qualified 
personnel or just contact your Coemar service near you. 

Question 

Possible cause 

Suggested solution 

Reflection does not power on. 

-

Projector not powered on:  

 
 
 

1-Make sure the power cord is plugged in 
or test the input voltage. 
 

Reflection does not answer to DMX 
signal. 

DMX signal may not reach Reflection . 

Inspect the cable connection, correct 
poor connections or inefficient repair or 
replace damaged cables. 
Check DMX address of the unit. 

I set Reflection as MASTER unit but it 
does not perform any program. 

1-There is another unit set as MASTER. 
2-The DMX signal is present. 
3-Any program has not been set. 

1-Search for the other MASTER unit and 
set it as SLAVE 
2-Remove eventual DMX patch. 
3-Set a program on the MASTER unit. 

Reflection is not recognized by DR1 Plus. 

ID set to 0 or another unit in the chain is 
set with the same number.. 

Set an ID number different from 0 and 
from any other unit in the chain. 

 

 

 

Information on disposal of the equipment 

 

 

The equipment at the end of its useful life must be disposed of at an appropriate recycling center for 
waste electrical and electronic equipment. The treatment and disposal of environmentally friendly, helps 
prevent potential negative environmental and health and promote the reuse and / or recycling of 
materials making up the equipment. Illegal disposal by the user includes the application of administrative 
sanctions provided by law.

 

 

 

Summary of Contents for Reflection FullSpectrum



























Reviews: