background image

UPLOAD function

Using this function it is possible to upload software to the 

Pin Lite LED

using a 

DR1+

For further information, consult the DR1 manual.

DOWNLOAD function

Using this function it is possible to download software from the 

Pin Lite LED

to a 

DR1+

For further information, consult the DR1 manual.

10.5. Error messages using DR1

MESSAGE CODE

DESCRIPTION

DTER

DATA Error
The initial configuration settings are fautly or have been loaded incorrectly. The projector has loaded its default
configuration. Turn the projector off and on again and if the error persists the EEPROM is either defective or
absent; refer to your 

Coemar

service centre for a replacement component.

ADER

DMX ADDRESS Error
The projector is not receiving all the DMX channels necessary for its operation. Check the DMX address and the
control console operation. Note that some controllers may not generate all 512 channels of signal. 

MAER

MASTER MODE Error
This message indicates that the user has attempted to set the unit to MASTER mode whilst DMX signal is still
being received. Detach any DMX control signal or remove MASTER mode settings.

menu

AOO1

FUNC

enter

RESE

reset

Reset function

M I N.R 

red led alignment

Alignment led red minimum intensity

enter

0001

enter

+

o

0010

ALIG

 

alignment

Colour setting

+

o

M I N.G

led green alignment

Alignment led green minimum intensity

enter

0001

enter

+

o

0012

+

o

M I N.B

led blue alignment

Alignment led blue minimum intensity

enter

0001

enter

+

o

001 5

+

o

MAX.R

led red alignment

Alignment  led red maximum intensity

enter

0250

enter

+

o

0255

+

o

MAX.G

led green alignment

Alignment led green maximum intensity

enter

0250

enter

+

o

0252

+

o

MAX.B

led blue alignment

Alignment led blue maximum intensity

enter

0250

enter

+

o

0248

+

o

END

end

To end the electronic calibration
procedure and to record it

enter

A001

+

o

+

o

enter

UPLD

 

Upload

Software upload from DR1+

+

o

--

0000

Upload value

SURE

enter

enter

DULD

 

Download

Software download to DR1+

+

o

--

0000

Download value

SURE

enter

enter

es.

es.

es.

es.

es.

es.

Press together 

enter

 and 

menu

 keys for

10 seconds: the display will show this menu

19

English

Summary of Contents for PIN LITE LED























Reviews: