MBER
:
COMMUNICATION Error
This message indicates that the motherboard within the unit is not communicating properly with the con-
trol source. Check the connectors located on both boards.
OPER
:
PAN ENCODER Error
This message indicates that there is a problem with the PAN encoders. Check the sensors on the encoder
wheel located near the pan movement motor, as well as the relevant cabling.
OTER
:
TILT ENCODER Error
This message indicates that there is a problem with the TILT encoder locate on the fixture yoke. Check the
sensors on the encoder wheel located near the pan movement motor, as well as the relevant cabling.
SNER
COMMUNICATION Error
This message indicates that the motherboard within the unit is not communicating properly with the con-
trol source. Check the connectors located on both boards.
EPER
:
EEPROM Error
The EEPROM is either defective or absent; refer to your coemar service centre for a replacement compo-
nent.
DTER
:
DATA Error
The initial parameter settings are incorrect or corrupt; the projector has reloaded its factory default settings.
Turn the projector off and on again. Should the error reoccur, refer the unit to your authorised coemar ser-
vice centre to have the EEPROM check and possibly replaced.
ADER
:
DMX addressing Error
The projector is not receiving all DMX channels needed to operate correctly. Check the DMX address indi-
cated on the display and the channel numbers being outputted from the controller. Note that not all con-
trollers will output all 512 channels.
S1ER
:
Control Circuit Error relating to position sensors for 5 motors. Sensor not reading the
magnet.
Check for the presence of power to the PCB and the condition of the connectors and cabling between the
PCB and the sensors. Additionally, check motors and/or cogs for any impediments as well as the proper
position of the cabling connectors.
S2ER
:
Control Circuit Error relating to position sensors for 4 motors (located in the yoke at
right when
viewed from the rear of the unit). Sensor not reading the magnet. Check for the presence of power to the
PCB and the condition of the connectors and cabling between the PCB and the sensors. Additionally,
check motors and/or cogs for any impediments as well as the proper position of the cabling connectors.
S3ER
:
Control Circuit Error relating to position sensors for 4 motors (located in the yoke at left
when
viewed from the rear of the unit). Sensor not reading the magnet. Check for the presence of power to the
PCB and the condition of the connectors and cabling between the PCB and the sensors. Additionally,
check motors and/or cogs for any impediments as well as the proper position of the cabling connectors.
C1ER
:
Position Error in colour wheel number 1 (closest to lamp). Sensor not reading the
magnet.
Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel.
C2ER
:
Position Error in colour wheel number 2. Sensor not reading the magnet.
Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel.
G1ER
:
Position Error in gobo wheel number 1 (closest to lamp). Sensor not reading the
magnet.
Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..
G2ER
:
Position Error in gobo wheel number 2. Sensor not reading the magnet.
Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..
R1ER
:
Position Error in gobo indexing on wheel 1. (closest to lamp). Sensor not reading the
magnet.
Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..
R2ER
:
Position Error in gobo indexing on wheel 2. Sensor not reading the magnet.
Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
24. Error messages
26
English
Summary of Contents for iSPOT 585 MB
Page 2: ......
