25
English
INSTALLER INSTRUCTIONS ONLY
The display panel at the rear of the
iSpot 575
allows for the electronic alignment of the projector’s motors in the optical
system. This procedure is performed by
coemar
at the factory. It may be useful to perform this procedure in the case of
internal components being replaced.
Altering the factory settings may radically alter the functioning of the projector. Carefully read all of the following prior to
attempting any changes.
electronic calibration
Important Note
: electronic calibration is only possible if the projector is connected to a
DMX 512
source.
1) Press the menu button.
2) Press the + or - button until the display shows
RESE
(for reset).
3) Press the enter button to confirm your selection then immediately and simultaneously press and hold the
menu
button,
holding both pressed for at least
30
seconds. The motors of the unit will perform a reset and the display will show
–- –- –- –-
for some few seconds, indicating that you have entered the electronic calibration mode.
Note
: Simultaneously pressing the
+
and
–
buttons will return the calibration value to the default value of 128.
☞
menu
☞
PNAL
pan alignment
Pan movement alignment
T L A L
tilt alignment
Tilt movement alignment
SH R
shutter alignment
Shutter’s right half alignment
SH L
shutter alignment
Shutter's left half alignment
C1AL
color wheels alignment
Color wheel 1 alignment
C2AL
color wheels alignment
Color wheel 2 alignment
FOCU
focus alignment
Focus system alignment
G1AL
gobo wheel 1 alignment
Gobo wheel 1 alignment (closest to the
lamp)
G2AL
gobo wheel 2 alignment
Gobo wheel 2 alignment
GR1
gobos alignment
Gobo wheel 1’s rotating gobos alignment
GR2
gobos alignment
Gobo wheel 2’s rotating gobos alignment
PRAL
prisms alignment
rotating prisms alignment
IRIS
iris alignment
iris diaphragm alignment
LEAL
lenses alignment
Focusing lenses alignment
END
end
To end the motors’ electronic alignment
procedure and confirm it
☞
+
o
–
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 4 0
☞
+
o
–
AOO1
☞
+ o –
press together in order to have access to
the motors electronic alignement menu
☞
+
o
–
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 0
enter
menu
RESE
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 3 0
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 5
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 3 5
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 3 2
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 7
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 1
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 4 0
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 7
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 7
☞
enter
A001
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 7
19. Electronic motor alignment
www.carlosmendoza.com.mx
