manualshive.com logo in svg

Cobra Y173V, Service Manual

Share
Download
Cobra Y173V Service Manual Download Page 42

40 

4. DISASSEMBLING AND SERVICING 

 

 

 

 

WHEEL PULLER 
(Commercial 
Available) 

FLYWHEEL 

 

 

 

 

 

4-4-7

 

Flywheel 

①

Removal

： 

a)

 

Holding the flywheel with a commercially 

available strap wrench, remove the nut 

（

M14

）

. 

b)

 

Disassemble the starter cut and impeller. 

 
 
 
 
 

c)

 

Remove with a commercially available flywheel puller. 

 

 

 

 

Do not hit the flywheel with a hammer. 

 

Avoid the magnet section when attaching the puller. 

② 

Installation 

a)

 

Clean the tapered part of dirt, oil grease and 

other foreign material before installation. Be sure 

that there is no washer and other foreign material 

on the magnetic part. 

b)

 

Set the key in the key groove. 

c)

 

Install the flywheel over the crankshaft. 

FLYWHEEL 

BRAKE 

 

 

The flywheel may push the key out of its slot, check after 
installation.

 

 

 

Flywheel (cast iron) 

 

Attach by aligning the four small holes in the flywheel. 

 

Attach by aligning the lug on the rear side of the starter cup with the small hole at the 

center of the flywheel. 

Summary of Contents for Y173V



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands