Cobra Y173V Page 10 Service Manual Download

Page: 10 / 66

2. DIMENSION AND TORQUE

2-4

Torque Value

ITEMS

FASTENERS

TORQUE VALUE (N·m)

Connection-Rod Bolt

M7×32

15±0.5

Governor Gear Bolt

M6×12

11±1

Crankcase Cover Bolt

M8×50

26±2

Spark Plug

M14-1.25

18±2

Cylinder Head Bolt

M8×50

26±2

Rotation Shaft Locked Nut

M6 × 0.5

11±1

Cylinder Head Cover Bolt

M6×14

10±2

Ventilation Chamber Cover Bolt

M6×12

7±1

Side Shield Bolt

M6×10

10±2

End Shield Bolt

M6×10

10±2

Brake Bolt

M6×35

11±1

Flywheel Nut(Cast Iron)

M14×1.5

80±6

Ignition Wire Bolt

M6×25

11±1

Fuel Tank Support Bolt

M6×12

10±2

Fuel Tank Bolt

M6×22

8±1

Recoil Starter Reel Nut

10±2

Throttle Control Sub Assemble Bolt

M6×10

10±2

Air Cleaner Nut

M6×1.0

10±2

Muffler Cover Nut

M6×1.0

10±2

Engine Cover Nut

M6×1.0

10±1

Drain Plug

M10 × 1.25

18±2

For unspecified bolt, screw and nut, refer to the standard torque value.

Summary of Contents for Y173V



































































Search results

Summary of Contents for Y173V

Reviews:

Related manuals for Y173V

Brands by name

Popular brands

Cobra Y173V, Service Manual

Search results

Summary of Contents for Y173V

Reviews:

Related manuals for Y173V

Brands by name

Popular brands