Cobra Y173V Page 14 Service Manual Download | Manualshive

Page: 14 / 66

background image

3. MAINTENANCE

12

3-3

Air Cleaner

                                     BREATHE TUBE
                                                                GASKET
                                                                             CASE
                                                                              NUT M6
                                                                                               PAPER FILTER ELEMENT

FOAM FILTER ELEMENT

COVER

Wash the engine each 50 hrs (or 3 months). (Wash more frequently in dust area)



Remove the air cleaner cover and take the element out.



Change the damaged element.



Clean the element before reusing.

Clean the element

：

Foam Element

Wash the element with detergent and dry it.

Immerse the element into the oil and squeeze the excessive oil. The element should

be wet, but not drop the oil.

Paper Element

Blow the compressed air from the inner side or lightly tap to move the dust. If dirty

badly, replace in time.



Be careful to prevent dirt from entering the air duct that leads to the carburetor.



Place the foam element over the paper element, and cover the case cover on.

«
...
12
13
14
15
16
...
»

Summary of Contents for Y173V



































































Reviews:

No comments

Related manuals for Y173V

Brand: Kohler Pages: 4

Brand: GRITAL Pages: 4

Brand: Team Orion Pages: 2

Brand: Yamaha Pages: 30

Brand: KONTRONIK Pages: 6

Brand: Bodine Pages: 8

Brand: Toyota Pages: 525

Brand: Volvo Pages: 8

Brand: Winterthur Gas Pages: 495

Brand: Electric Drive Engineering Pages: 19

Brand: Nanomotion Pages: 42

Brand: Honda Pages: 156

BLACK BLOCK 62-SGW

Brand: TOMAHAWK SPORT Pages: 20

Brand: M Confort Pages: 68

Brand: Briggs & Stratton Pages: 16

USB Protocol Suite

Brand: LeCroy Pages: 107

Brand: pro.point Pages: 64

Brand: Stiga Pages: 161

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands