background image

NOTE: 
ALL  GAS  FITTING  MUST  ONLY  BE  CARRIED  OUT  BY  A 

QUALIFIED SERVICE PERSON. 

 
1.  Cobra Stock Pots do not require an electrical 

connection, they function totally on the gas 
supply only. 

2.  It is essential that the gas supply is correct for the 

appliance to be installed and that adequate 
supply pressure and volume are available.  The 
following checks should be made before 
installation:- 
a. 

The Gas Type 

the appliance has been  

supplied for is shown on coloured stickers  
located above the gas entry point and next 
to the rating plate.  Check that this is correct 
for the gas supply the appliance is being  

installed for.  The gas conversion procedure is 
detailed in the ‘Gas Conversion Section’ at 
the rear of this manual. 

b. 

Supply Pressure 

required for this appliance is 

shown in the ‘Specifications’ section of this 
manual.  Check the gas supply to ensure that 
adequate supply pressure exists. 

c. 

Input Rate 

of this appliance is also shown on 

the Rating Plate fitted to the lower RH side of 
the appliance and in the ‘Specifications’  
section of this manual.  The input rate should 
be checked against the available gas supply 
line capacity.  

Particular note should be  

taken if the appliance is being added to an 
existing installation.

 

 

NOTE: 
It  is  important  that  adequately  sized  piping  runs  

directly  to  the  gas  connection  joint  on  the  
appliance, with as few tees and elbows as possible 
to give maximum supply volume. 
 

3.  Fit the supplied gas regulator into the gas supply 

line as close to the appliance as possible. 

 
NOTE: 
The  gas  pressure  regulator  provided  with  this  
appliance  is  convertible  between  Natural  Gas  and 
LPG as per ‘Gas Conversion Section’ in this manual. 
Ensure  regulator  is  converted  to  the  correct  gas 

type that the appliance will operate on. 
Regulator outlet pressure is fixed ex-factory for gas 

type  that  regulator  is  converted  to  and  it  is  NOT  to 
be adjusted. 

 

Regulator connections are 

3

/

4

" BSP female. 

Connection to appliance is 

3

/

4

" BSP male. 

(Refer to 'Specifications' section for gas supply  
connection location). 

 

4.  A suitable joining compound which resists the 

breakdown action of LPG must be used on 
every gas line connection, unless compression 
fittings are used. 

 

NOTE:  A  Manual  Isolation  Valve  must  be  fitted  to 

individual appliance supply line. 

 

5.  Locate the appliance into its final operating 

position and using a spirit level, adjust the legs so 
that the unit is level and at the correct height. 

6.  Connect the gas supply to the Stock Pot burner 

of the appliance. 

7.  Check Burner Operating Pressure is as shown in 

the ‘Specifications’ section, ‘Gas Supply  
Requirements’ tables. (Measure at the gas  
burner ‘Operating Pressure’ test point on the 
appliance as shown below. 

NOTE: 
Measure the gas burner pressure at the Pressure Test 
Point  located  on  the  gas  manifold  with  the  main 
burner operating at the 'High Flame' setting. 

 

8.  Check all gas connections for leakages using 

soapy water or other gas detecting equipment, 
with the main burner operating. 

9.  Verify the operating pressure remains correct. 

 

D

O

 

NOT

 

USE

 

A

 

NAKED

 

FLAME

 

TO

 

CHECK

 

FOR

 

GAS

 

LEAKAGES

Pressure Test Point 

Gas Manifold 

Summary of Contents for CSP6




















Reviews: