manualshive.com logo in svg

CoaguSense INR, User Manual

Share
Download
CoaguSense INR User Manual Download Page 50

 

 

Page 46 

 

17.  Cleaning and Disinfecting the Meter 

No  maintenance  is  required  other  than  routine  cleaning  and/or 
disinfecting.   

When  the  power  is  off  and  the  USB  cable  is  not  connected,  the 
meter  housing  can  be  cleaned  and  disinfected.  Wipe  all  exposed 
surfaces  with  Healthcare  Bleach  Germicidal  Wipes  containing 
Sodium  Hypochlorite  (EPA  No.  67619-12)  for  a  contact  time  of  1 
minute to pre-clean blood and other body fluids. Caution should be 
taken to not get fluids inside the meter through the test strip port, 
data  transmission  port  or  battery  compartment.  Dispose  of  the 
used towelette. The meter should be allowed to air dry before use.   

 

The test strip is designed to contain the patient sample, preventing 
it from entering the meter.  Do not clean/disinfect inside the meter 
where  the  test  strip  is  inserted.  Cleaning  this  area  should  be 
avoided.    Please  call  Technical  Support  at  1-866-903-0890  if  this 
area requires cleaning/disinfecting. 

WARNING

: Do not put the meter in liquid. Do not 

allow liquids to get inside the meter or into any of 
the  connectors  or  plugs  on  the  meter.  If  you 
suspect  any  physical  damage  or  deterioration  of 
the  meter  (such  as  cracking  or  gross  distortion), 
or  if  the  meter  does  not  turn  on  after  cleaning, 
call Technical Support.

 

 

 

Summary of Contents for INR


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands