manualshive.com logo in svg

CoaguSense INR, User Manual

Share
Download
CoaguSense INR User Manual Download Page 2

 

 

 

 

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval 

system or translated into any language or computer language, in any form or by any means, 

including,  but  not  limited  to,  electronic,  magnetic,  optical,  chemical,  manual,  or  otherwise 

without written permission of CoaguSense. CoaguSense has made every reasonable effort to 

ensure  that  all  the  information  contained  in  this  manual  is  correct  at  the  time  of  printing. 

However, CoaguSense reserves the right to make any changes necessary without notice as 

part of ongoing product development. 

If  you  have  any  questions  or  concerns  with  the  Coag-Sense

®

  Prothrombin  Time  (PT)/INR 

Monitoring System, please contact CoaguSense Technical Support at: 

 

CoaguSense, Inc. 

48377 Fremont Blvd., STE. 113 

Fremont, CA 94538 

USA 

Toll Free: 1-866-903-0890 

E-Mail: 

[email protected]

 

 

 

 

 

© Copyright 2019, CoaguSense, Inc. All rights reserved. 

Coag-Sense is a registered trademark of CoaguSense, Inc.

 

Summary of Contents for INR


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands