Cloos QINEO Micro 300, Operating Instructions/Spare Parts List

Page: 17 / 33

Micro 300
Cod.006.0001.1362
25/03/2013 v2.0
ENGLISH
17/32
10.2.2 DC TIG P
ARAMETERS
S
ETTING
(GAS
MENU
)
S3
Hold down the button for 3 seconds to gain access to the 2nd level Menu
 Po.G. The acronym relative to the setting to be edited is shown on display D1

3 The value relative to the selected setting appears on display D2
E1
Use the encoder to scroll the list of settings to edit
Tab. 8 GAS Menu parameters in continuous TIG mode
E2
Using the encoder, edit the value of the selected setting
Press any button to save the setting and quit the Menu
Tab. 8 GAS Menu parameters in continuous TIG mode
PARAMETER MIN DEFAULT MAX NOTES
Po.G. POST-GAS TIME 0s 3s 10.0s
When a synergic program is loaded the default value of the parameter is
defined automatically by the software and the message “SYN” will be shown on
the display
10.3 MIG/MAG WELDING
SEL1
Set the selector to the symbol to select MIG/MAG welding mode MIG/MAG
S5
Press the button to select the torch trigger procedure
The following torch trigger procedures are available:
(2 STEPS) (4 STEPS) (3 LIVELLI)
10.3.1
S
ETTING
MIG/MAG
PARAMETERS
(M
AIN
W
ELDING
P
ARAMETERS
)
S2
Press the button to scroll the list of settings to edit

The LED associated with the selected setting will illuminate

The value relative to the selected setting appears on display D1
The following settings are available
WIRE FEED RATE AMPERES THICKNESS PROGRAMS
E1
Using the encoder, edit the value of the selected setting
Tab. 9 Main welding parameters in MIG/MAG mode
The value is saved automatically
Tab. 9 Main welding parameters in MIG/MAG mode
PARAMETER MIN DEFAULT MAX NOTES
WIRE FEED RATE 1m/min 20m/min
MIG/MAG WELDING CURRENT Syn Not enabled with manual program P0
THICKNESS Syn Not enabled with manual program P0
PROGRAMS P0 P0 P34 Tab. 10 Programmed synergic curves
Tab. 10 Programmed synergic curves
WIRE DIAMETER
0.8 1.0 1.2 1.4
ACRONYM WIRE MATERIAL (GAS MIXTURE)
P0 P0 P0 P0 MAn MANUAL
P1 P2 P3 -- FE SG2/SG3 (80%Ar-20%CO2)
P4 P5 P6 -- FE SG2/SG3 (92%Ar- 8%CO2)
P7 P8 P9 -- FE SG2/SG3 (100%CO2)
P10 P11 P12 -- S.S. INOX 308 (98%Ar-2%CO2)
P13 P14 P15 -- S.S. INOX 316 (98%Ar-2%CO2)
P16 P17 P18 -- AL AlMg5 (100%Ar)
P19 P20 P21 -- AL AlSi5 (100%Ar)
P22 P23 P24 -- CU.S. CuSi3 (100%Ar)
P25 P26 P27 CU.A. CuAl8 (100%Ar)
-- -- P28 P29 rFC RFCW (80%Ar-20%CO2)
-- -- P30 P31 bFC BFCW (80%Ar-20%CO2)
-- -- P32 P33 MFC MFCW (80%Ar-20%CO2)
P
R
O
G
R
A
M
P34 -- -- -- nPr FREE PROGRAMS