background image

© 2004 directed electronics, inc.

27

user selectable features

N

NO

OTTEE:: Factory default settings are shown in bboolldd.

*

This feature is only available with optional IntelliStart connected.

**

This feature is only available with optional SmartWindows connected.

First

Press

Then

Press

Add new remote

(autolearn)

Set PIN code

(default = 2)

New remote learn

arm/disarm only

Auto (passive)

arm 

off

/on

Select siren

sounds

New remote learn

accessory A channel

Chirps

off/on/

quiet

FACT II off/

on

New remote learn

accessory B channel

Auto lock

off/

ignition

/rpm

Remote valet

off/

on

New remote learn

silent mode

Auto unlock

off/

ignition

Entry delay

 off

/on

New remote learn

remote valet

Auto (passive)

arm and lock

off

/on

Reset to default

(except transmitter

and valet code)

New remote learn

remote start*

Siren duration

30

/60/90

Panic off/

on

New remote learn

window down/vent**

Second unlock

off

/on

Autostart setting*

(

off

/battery only/

temp only/

battery and temp)

New remote learn

accessory C channel

Not used

BlackJax 

off

/on

Clear all remotes

Summary of Contents for intelliGuard 750


















































Reviews: