Clemco CMS-4 Operation Manual Download

Page: 29 / 29

CMS-4 IN-HELMET CARBON MONOXIDE MONITOR

Page 24



www.clemcoindustries.com



Manual No. 29872

8.0

REPLACEMENT PARTS

8.1

System Replacement Parts, Figure 33

Item

Description

Stock No.

(-)

CMS-4 CO Monitor Package

Includes items shown with asterisk (*) .... 29765

  1.  *  CMS-4 CO monitor, instrument only .......... 29766
  2.  *  Calibration kit  .............................................. 29767
  3.

Test gas,

* 25 ppm CO .............................................. 25573

Impurity-free ............................................ 11132

Calibration connector with

0.5 LPM fixed-flow slide valve ................. 25572

Calibration cup ........................................... 29764

Tubing, 3/16 ID, 2-feet required ................. 13074

7. * Velcro

tape, loop side

Included with kit 29870, shown in Figure 34

8. * Velcro

tape, hook side

Included with kit 29870, shown in Figure 34

9. * Mounting strip assembly

used with Apollo 60 and 600 only

Included with kit 29870, shown in Figure 34.

OP E N

CLEMCO

Figure 33

8.2

Monitor Replacement Parts ‒ Figure 34

NOTE: There are no serviceable parts within the
CMS-4 case. Do not remove the four screws holding
the upper and lower case together or try to separate
the case.

Item

Description

Stock No.

1. * Sensor, CMS-4 ........................................... 29768
2.

Retainer, sensor ......................................... 29769

Retainer, battery ......................................... 29770

Gasket, sensor .......................................... 29771

Gasket, battery retainer ............................. 29772

  6.  * Filter, hydrophobic, each   .......................... 29868
  7.  * Filter, charcoal, pack of 5 .......................... 25564
  8.

Mounting clip ............................................. 29869

Battery, 3V Lithium coin ............................. 24619

or purchase model CR2450 locally

10.

Service kit, includes items 10a thru 10e .... 29870

10a Screw set (2), sensor and battery retainers

10b Velcro

tape, loop side, 1" x 1-1/4"

10c Velcro

tape, hook side, 1" x 2" (qty. of 2

10d Mounting strip, transparent (qty. of 2)

10e Spring pin (qty. of 2)

* Make sure a new hydrophobic filter (Item 6) and
charcoal filter (Item 7) are available so they can be
replaced when changing the sensor (Item 1).

Figure 34

10a

10b

10e

10c

10d

Summary of Contents for CMS-4






























Search results

Summary of Contents for CMS-4

Reviews:

Related manuals for CMS-4

Brands by name

Popular brands

Clemco CMS-4, Operation Manual

Search results

Summary of Contents for CMS-4

Reviews:

Related manuals for CMS-4

Brands by name

Popular brands